'Unitech DIP Sulphate Cement'. Factory applied, grey coloured sulphate cement. Mix as per work instructions issue no. 'QAP-MOS-UNITECH 212-13- rev1', dated 21st December 2020. Cure for 6 hours@40°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5105-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'PMSP5065-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'Rashmi Cement 43 Grade OPC'. Factory applied, grey coloured Ordinary Portland cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MEKCOAT Liquid Membrane Coating'. Factory applied, two-component, blue coloured polyurethane coating. Mix in a 1:1 volume ratio. Cure for 24 hours@23-24°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘EUROKOTE® 46-20’. Factory applied, red-brown coloured, two-part epoxy resin coating. Mix and apply as per manufacturer's technical data sheet 'Doc. 087' dated 01/07/2011. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001 Blue`, factory applied, blue coloured, fusion bonded epoxy coating. 'Jotaguard VA 5001 Red`, factory applied, red coloured, fusion bonded epoxy coating was added to the approval in June 2023. Apply both coatings as per Jotun Technical Data Sheet issued 9th November 2015. Cure for 5 minutes@245°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Epoxy phenolic FBE-4 RAL 5010'. Factory applied, blue coloured epoxy phenolic coating. Apply as per manufacturer's instructions dated '11/20'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Karumel EX4412 Blue & Grey’. Factory applied, blue or grey coloured, epoxy resin based powder coating. Apply and cure as per manufacturer’s instructions reference 'PCA-21062901', issued August 2021. For use with water up to 85°C.
'CeramycGuard for use with QuartzSeal'. Site applied, white coloured (once mixed) polymer based concrete surface treatment. 'CeramycGuard’ is a three-component base coat comprising of Part A (clear liquid), Part B (grey powder) & Part C (clear liquid). Mix Parts A, B & C in a volume ratio. Rest for two minutes, apply as per manufacturer's instructions for use 'version 2' dated 'April 2021' and then cure for 24 hours@21°C. ‘QuartzSeal' is a white coloured, single-component topcoat. Apply as per manufacturer's instructions for use 'version 2' dated 'April 2021'. Cure for 7 days@21°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Jazeera Proofex (formerly known as Jazeera Proof DW)'. Site applied, two-component, grey coloured cementitious coating. Mix Part A (grey coloured powder) with Part B (white, opaque liquid) in a 2:1 mass ratio. Cure for 28 days@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Acrylatik'. Site applied, Acrylate primers available in white, red, blue and black colours. Apply as per manufacturer's instructions 'Appendix No. 1, TU 2316-002-92 872914-2016' dated '11.02.2016'. Cure for 20 minutes@20°C and then 20 minutes@90°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ajpipe GRP Pipe'. Beige coloured GRP pipe manufactured by continuous filament winding. For use with water up to 23°C. From February 2024, the pipe is for use with water up to 60°C.
'Purolite® A600E/9149'. Yellow coloured ion exchange resin. For use with water up to 23°C.
'Mapex® AN4920SN FWB50 & GITOP® G3A2 M01FWB'. Black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'3301 black (330160415BLK)'. '3301 black (330130415BLK)' was added to the approval in November 2023. Black coloured, single sided polyethylene foam tapes with acrylic adhesive system. For use with water up to 23°C.
'ajpipe HDPE Pipe'. Black coloured (with blue external stripes), extruded PE100 pipe. For use with water up to 50°C. From January 2024 the pipe is for use with water up to 60°C.
'Revolve 6405U Natural (appears white coloured) & Revolve M-1585 Black (black coloured)'. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
‘Revolve N-840 (HD3850) & Revolve M-750 DR Black’. Revolve N-840 (HD3850) is a white coloured polyethylene material & Revolve M-750 DR Black is a black coloured polyethylene material. Both are manufactured by rotational moulding. For use with water up to 85°C. Please note that ‘Revolve N-840 (HD3850)’ was formerly known as ‘Revolve N-840 (6850)’.
Page 8 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
