‘NMSP2104 M'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual ‘specification no. PIN-10’, revision no. '0' dated '15/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EDELPOXY FNSL 151'. Factory applied, two-component, grey coloured epoxy coating. Mix base and hardener in a 2:1 volume ratio and apply as per manufacturer's instructions for use, reference number 'PC 151', dated January 16, 2015. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NATZINC EP9015 SC PART A-BI.5431’ primer for use with ‘HYDRALFUN AC NOIR PAM -CZL8579’ finish/topcoat. Factory applied, black coloured (once mixed and applied), two-part epoxy primer for use with acrylic coating. Mix base & hardener of primer in a 100:10 weight ratio and apply one coat as per manufacturers TDS ‘NATZINC EP9010 BI 5431’, dated ‘February 2024’. No cure required. Apply one coat of the topcoat as per manufacturers TDS ‘HYDRALFUN AC NOIR PAM CZL8579’, dated ‘July 2018’ and cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SUPERPOXY 5000RP'. Factory applied, two component, blue coloured epoxy coating. Mix Parts A & B in a volume ratio of 3:1 and apply as per manufacturer's instructions issue reference 'SPI 20170413 ' dated September 1st, 2016. Cure for 58 hours@24°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaguard CSF 585/Blue' (included on the initial approval) is for use with water up to 50°C. 'Sigmaguard CSF 585/RAL5017’ was added to the approval in December 2025 and is for use with water up to 40°C. Factory applied, blue coloured, two-component, solvent-free epoxy coatings. Mix parts A & B in a volume ratio of 77.5:22.5 and apply as per manufacturer's Product Data Sheet '7785', dated 'August 19, 2022'. Cure for 12 days@20°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hydroplate 1914'. Site applied, two-component, white coloured (once mixed and applied) Epoxy-polyamine coating. Mix parts A & B in a 3:1 weight ratio and apply as per manufacturer's Product Data Sheet 'B034', dated 'September 2024'. Cure coat 1 for 48 hours at 15°C. Cure coat 2 for 21 days at 15°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Synolite 5410-P-4'. Pink/brown coloured polyester laminate/GRP material manufactured by hand-lay. For use with water up to 23°C.
‘DENYL 6 5010 NERO 0300, DENYL 6 3010 NERO 0300, DENYL 6 1510 NERO 0300, DENYL 6 5010 NERO, DENYL 6 3010 NERO & DENYL 6 1510 NERO’. Black coloured, injection moulded, glass fibre filled PA6 materials. For use with water up to 85°C.
'Genestar G1350A-M47WF Black'. Black coloured, polyamide 9T material for injection moulding and extrusion purposes. For use with water up to 85°C.
'SAFE 10 (H10 + H09, H17 + H04 and N08 + N04)' pipes. Extruded, dual-layered PE pipes comprising of a black coloured inner layer and blue coloured outer layer. Please note that the codes in brackets denote the raw material combinations and only these combinations are approved. In April 2025 ‘H10, H17 & N08’, extruded, single-layered, black coloured PE pipes were added to the approval. Only pipes marked with ‘H10, H17 or N08’ are approved. For use with water up to 40°C.
Page 660 of 1043
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
