Range of manually operated balancing valves incorporating bronze bodies, rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 10.0 Bar Maximum operating temperature 100.0°C
Range of magnetic scale reducers with metal bodies, for use with copper pipe (manufactured to EN 1057). Maximum working pressure 12 Bar. Maximum operating temperature 30°C.
Range of polyethylene pressure vessels with spun fibreglass casing. Maximum working pressure 10.0 bar Maximum operating temperature 50°C.
'YHR-GFS Enamel'. Factory applied, dark blue coloured Enamel coating. Mix enamel powder with water in a ratio of 7:3 and apply two coats as per manufacturer's TDS 'YHRGFS2504', version 'V0', dated '2025/3/27'. Cure for 20 minutes@120°C and fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the mixing, curing & firing conditions that appear on the approval. If the mix and/or cure and/or fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusion Bonded Epoxy (IMP-FBE) Cobalt Blue RAL 5013'. Factory applied, dark blue coloured epoxy coating. Pre-heat the substrate to 200°C and spray apply one coat at 120°C as per manufacturer's TDS 'YHRFBE2504', version 'V0'. dated '2025/3/27'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BFSC MAS S&MDN 25'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a mass ratio of 1:2.35:0.45 and apply as per manufacturer's TDS 'SGMAS20111012-01', dated '2011.10.12'. Cure for 19 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-02 Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'Ascent02-2511', dated '2025.11.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EPLAMID HT00 GFR 40 FW BK'. Black coloured, injection moulded, glass fibre reinforced PA 6T/6I material. For use with water up to 85°C.
'ELTEX® SUPERSTRESS TUB124N6000'. Blue coloured, compression moulded HDPE material. For use with water up to 23°C.
'RAMSET ChemSet™ Reo502™ Xtrem™’ & ‘RAMSET ChemSet™ Epcon™ G5 Xtrem™'. Site applied, brick coloured (once mixed), chemical anchor resins, each supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'NOV. 25'. Cure for 24 hours@21°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 603 of 652
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
