‘Cicoprime®25 Primer and Cicoshield®PW100 Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply Cicoprime®25 Primer in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated October 2023. Cure for 2 hours@25°C. Then mix Cicoshield®PW100 Coating in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated August 2024. Cure for 1 minute@25°C. For use with water up to 85°C.
'SMS-FBE-Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS 'Document Code 53', 'Publication No 5', dated 01.03.2024. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BFSC Foug SDN’. Factory applied, grey coloured, blast furnace slag cement intended to line pipes. Mix sand and cement in a mass ratio of 1.5:1, then add water in a water/cement mass ratio of 0.36:1 and apply as manufacturer's instructions. Cure for 48 hours@23°C, 70% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ARC SD4i(E)'. Factory applied, grey and blue coloured, two-part epoxy coatings. Mix parts A and B in a weight ratio of 2.5:1 and apply as per manufacturer's Application Instructions 'EN-085034EU', dated '01/2025'. Cure for 72 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ARC 858(E)'. Factory applied, dark grey coloured, two-part epoxy coating. Mix parts A and B in a weight ratio of 4:1 and apply as per manufacturer's Application Instructions 'EN-085013EU', dated '08/2024'. Cure for 54 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'novapress®BASIC'. Orange coloured NBR/aramid fibre gasket material, manufactured by calendaring. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
'BONDSTRAND GRE Pipe'. Dark green coloured, GRE pipe manufactured by filament winding. For use with water up to 85°C.
'LLS-Magnet'. Grey coloured, pressed & sintered Strontium Ferrite magnet in the form of a washer. For use with water up to 85°C.
'IMAMAG HF85'. Grey coloured Strontium ferrite magnet manufactured by isotropic sintering. For use with water up to 85°C.
'ULTRAMID® F3EG10 AQUA SW23285'. Black coloured, injection moulded PA6.1 material. For use with water up to 85°C.
Page 544 of 790
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
