Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 8.6 bar. Cold water use only.
'Nav-Coat Bitumen Paint 001 Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's product information sheet issued '10.07.2009'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZMF7405'. Factory applied, blue coloured Enamel coating. Apply as per manufacturer's TDS 'Version 01', issue date 'December 1, 2025'. Dry for 15 minutes@100°C and then furnace fire for 10 minutes@860°C. For use with water up to 85°C.
‘Nelfapox FW Inert Cream'. Factory applied, cream coloured, two-component epoxy coating. Mix base and curing agent in a 6.8:2 volume ratio. Apply one or two coats as per manufacturer's Technical Data Sheet '999', revision date '24-03-2026'. Cure Coat 1 for 16 hours@20°C. Cure Coat 2 for 7 days@20°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RTPE100HP' (black coloured with blue stripe) & 'RTPE100LP' (blue coloured) Pipes. Black or blue coloured, extruded HDPE pipes. For use with water up to 60°C.
'RTPE100HF' (black coloured) & 'RTPE100LF' (blue coloured) Fittings. Black or blue coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'CHINAUST F1 HDPE Pipes'. Black coloured (with blue stripes), extruded HDPE pipes. For use with water up to 65°C.
'CHINAUST F1 HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
'1021 3-ply Polyethylene Liner'. Blue coloured (transparent) LLDPE polyethylene liner, incorporating a heat weld, manufactured by blown film co-extrusion. For use with water up to 23°C.
'DC-E1M Fitting'. Black coloured, extruded and machined, PE fitting. For use with water up to 60°C.
'Hostalen PP XN125-P' & 'Hostalen PP XN112-I'. Off-white coloured (translucent), compression moulded PP materials. For use with water up to 60°C.
'FLPTFE – 12mm x 12M PTFE Tape'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'Smart S-IRV'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0141’, dated ‘29/11/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Smart S-IRE'. Site applied, light pink coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 17/0187’, dated ‘29/11/2023’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘Sika AnchorFix®-3030'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 17/0694’, dated ‘09/09/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 17/0694’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘Sika AnchorFix®-2+’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 14/0346’, dated ‘07/11/2025’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 14/0346’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'OLD B254 50N'. Black coloured, injection moulded IIR material. Shore hardness 50 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'KB60-E'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.2mm. For use with water up to 23°C.
Page 512 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
