Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with brass or DZR brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue, black or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
2Z126 FGAXXXB16NS01 range of brass gate valves or FGAXXXD16NS42 range of DZR brass body gate valves, with PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (MV40-1138.RS, MV40-1138 & MV40-1138.D models). Bronze body, bronze wedge and lock-shield (MV40-1153.LS & MV40-1138.LS models). Brass body, brass wedge and handwheel (MV40-1120 model only). Maximum working pressure 20.0 bar & 25.0 bar (model MV40-1153.LS only). Maximum operating temperature 85°C.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of non-rising spindle gate valves with bronze bodies, incorporating a hand wheel operating member. Maximum working pressure 16.0 Bar Maximum working temperature: 85C
Range of gate valves, (bronze bodies) incorporating either rising or non-rising spindle headworks and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies and stems, EPDM O-rings, with non-rising spindles with hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Range of scale inhibitors with chrome plated copper bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Cold water use only.
In-line electrolytic scale reducer with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
'Iupital F10-EW'. White coloured, injection moulded POM material. For use with water up to 85°C.
'8284873 HA002I INT 100 HYF WHITE SN80'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's TDS 'Revision Date: V2, 24.05.2024', 'Region: EMEA'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF-CM1'. Factory applied, grey coloured, sulphate resistant cement mortar. Mix cement mortar, sand & water in a 2:1:0.4 mass ratio and apply as per manufacturer's user instructions 'SF-CM1', 'Vision A1' dated '2024-7'. Cure for 12 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM119-1'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no.: LM-001', 'Edition: A', 'Issue date: 2024-JAN.-15th'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 448 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
