‘HDE-210xxx-xx’ range of brass press-fit fittings incorporating EPDM ‘O’-rings for use with copper pipes (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250615003

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

TAIZHOU DEOUNI FLUID CONTROL TECH. CO., LTD. logo and size on body.

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

Plug: HDE-210001-01: 15mm, HDE-210001-02: 22mm, HDE-210001-03: 28mm, HDE-210001-05: 35mm, HDE-210001-06: 42mm, HDE-210001-07: 54mm. Straight Connector: HDE-210002-01: 15mm*15mm, HDE-210002-02: 22mm*22mm, HDE-210002-03: 28mm*28mm, HDE-210002-05: 35mm*35mm, HDE-210002-06: 42mm*42mm, HDE-210002-07: 54mm*54mm. Male Connector: HDE-210003-01 : 15mm*½”, HDE-210003-02 : 22mm*¾”, HDE-210003-03 : 28mm*1”, HDE-210003-05 : 35mm*1¼”, HDE-210003-06 : 42mm*1½”, HDE-210003-07 : 54mm*2”. Female Connector: HDE-210005-01 : 15mm*½”, HDE-210005-02 : 22mm*¾”, HDE-210005-03 : 28mm*1”, HDE-210005-05 : 35mm*1¼”, HDE-210005-06 : 42mm*1½”, HDE-210005-07 : 54mm*2”. Elbow Connector: HDE-210006-01: 15mm*15mm, HDE-210006-02: 22mm*22mm, HDE-210006-03: 28mm*28mm, HDE-210006-05: 35mm*35mm, HDE-210006-06: 42mm*42mm, HDE-210006-07: 54mm*54mm. Male Elbow Connector: HDE-210007-01: 15mm*½”, HDE-210007-02: 22mm*¾”, HDE-210007-03: 28mm*1”, HDE-210007-05: 35mm*1¼”, HDE-210007-06: 42mm*1½”, HDE-210007-07: 54mm*2”. Female Elbow Connector: HDE-210008-01: 15mm*½”, HDE-210008-02: 22mm*¾”, HDE-210008-03: 28mm*1”, HDE-210008-05: 35mm*1¼”, HDE-210008-06: 42mm*1½”, HDE-210008-07: 54mm*2”. Tee Connector: HDE-210009-01: 15mm*15mm*15mm, HDE-210009-02: 22mm*22mm*22mm, HDE-210009-03: 28mm*28mm*28mm, HDE-210009-05: 35mm*35mm*35mm, HDE-210009-06: 42mm*42mm*42mm, HDE-210009-07: 54mm*54mm*54mm. Male Tee Connector: HDE-210010-01: 15mm*15mm*½”, HDE-210010-02: 22mm*22mm*¾”, HDE-210010-03: 28mm*28mm*1”, HDE-210010-05: 35mm*35mm*1¼”, HDE-210010-06: 42mm*42mm*1½”, HDE-210010-07: 54mm*54mm*2”. Female Tee Connector: HDE-210011-01 : 15mm*15mm*½”, HDE-210011-02 : 22mm*22mm*¾”, HDE-210011-03 : 28mm*28mm*1”, HDE-210011-05 : 35mm*35mm*1¼”, HDE-210011-06 : 42mm*42mm*1½”, HDE-210011-07 : 54mm*54mm*2”. Wall-Plate Elbow Connector: HDE-210012-01: 15mm*15mm, HDE-210012-02: 22mm*22mm, HDE-210012-03: 28mm*28mm, HDE-210012-05: 35mm*35mm, HDE-210012-06: 42mm*42mm, HDE-210012-07: 54mm*54mm. Wall-Plate Male Elbow Connector: HDE-210013-01: 15mm*½”, HDE-210013-02: 22mm*¾”, HDE-210013-03: 28mm*1”, HDE-210013-05: 35mm*1¼”, HDE-210013-06: 42mm*1½”, HDE-210013-07: 54mm*2”. Wall-Plate Female Elbow Connector: HDE-210015-01: 15mm*½”, HDE-210015-02: 22mm*¾”, HDE-210015-03: 28mm*1”, HDE-210015-05: 35mm*1¼”, HDE-210015-06: 42mm*1½”, HDE-210015-07: 54mm*2”. All threaded connection are BSP.

Product Images

Approval Holder:

TAIZHOU DEOUNI FLUID CONTROL TECH. CO., LTD.

Company Name

TAIZHOU DEOUNI FLUID CONTROL TECH. CO., LTD.

Address

No.3, Jinhai Road, Bin'gang Industry Zone, Ganjiang Town, Yuhuan, Zhejiang Province, 317610

Country

China

View All Listings by this Company

Manufacturer:

TAIZHOU DEOUNI FLUID CONTROL TECH. CO., LTD.

Company Name

TAIZHOU DEOUNI FLUID CONTROL TECH. CO., LTD.

Address

No.3, Jinhai Road, Bin'gang Industry Zone, Ganjiang Town, Yuhuan, Zhejiang Province, 317610

Country

China

View All Listings by this Company

‘EPH_WSP19_XXXX’ range of brass end feed and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250515011

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

Size and/or DOZ on body.

Installation Requirements:

R001

Expiry date:

31/05/2030

Model:

End Feed Fittings: Air vent cap: EPH_WSP19_0593 - 15mm. Wall Plate Elbow: EPH_WSP19_0608 - 15mm * ½” BSP (M). Male Coupler: EPH_WSP19_0618 - 15mm * ½” BSP (M), EPH_WSP19_0619 - 15mm * ¾” BSP (M), EPH_WSP19_0625 - 22mm * ¾” BSP (M). Female Coupler: EPH_WSP19_0635 - 15mm * ½” BSP (F), EPH_WSP19_0642 - 22mm * ¾” BSP (F). Female Elbow: EPH_WSP19_0663 - 15mm * ½” BSP (F). Male Elbow: EPH_WSP19_0676 - 15mm * ½” BSP (M). Threaded Brass fittings: Threaded Brass Blanking Nut: EPH_WSP19_0719A - ¼” BSP (F), EPH_WSP19_0720 - ⅜” BSP (F), EPH_WSP19_0721 - ½” BSP (F) - CHROME, EPH_WSP19_0721A - ½” BSP (F), EPH_WSP19_0722A - ¾” BSP (F), EPH_WSP19_0723 - 1" BSP (F). Threaded Brass Male Flanged Plug: EPH_WSP19_0726 - ½” BSP (M), EPH_WSP19_0727 - ¾” BSP (M), EPH_WSP19_0724 - ¼” BSP (M), EPH_WSP19_0728 - 1" BSP (M). Threaded Brass Reducing Bush: EPH_WSP19_0746 - M-F ½” BSP (M) * ¼” BSP (F), EPH_WSP19_0747A - M-F ½” BSP (M) * ⅜" BSP (F), EPH_WSP19_0749A - M-F ¾” BSP (M) * ½” BSP (F), EPH_WSP19_0750A - M-F 1” BSP (M) * ¾” BSP (F), EPH_WSP19_0751 - M-F 1” BSP (M) * ½” BSP (F). Threaded Brass Hexagon Nipple: EPH_WSP19_0761 - M-M ¼” BSP (M) * ¼” BSP (M), EPH_WSP19_2476 - M-M ⅜” BSP (M) * ⅜” BSP (M), EPH_WSP19_0763A - M-M ½” BSP (M) * ½” BSP (M), EPH_WSP19_0764B - M-M ¾” BSP (M) * ¾” BSP (M), EPH_WSP19_0765A - M-M 1” BSP (M) * 1” BSP (M). Threaded Brass Flanged Backnut: EPH_WSP19_0801 - ½” BSP (F), EPH_WSP19_0802A - ¾” BSP (F). Threaded Brass Female Socket: EPH_WSP19_0841 - ¼” BSP (F), EPH_WSP19_0843 - ½” BSP (F), EPH_WSP19_0844 - ¾” BSP (F), EPH_WSP19_0845 - 1” BSP (F). Tap extender: EPH_WSP19_2605 - ½” BSP (F) x ¾” BSP (M), EPH_WSP19_2609 - ¾” BSP (F) * ¾” BSP (M). Multi thread Nipple: EPH_WSP19_2599 - ¾” BSP (M) * ½” BSP (F) * 5/8” BSP (F) with rubber washer.

Product Images

Approval Holder:

Hangzhou DOZ Import & Export Co., Ltd

Company Name

Hangzhou DOZ Import & Export Co., Ltd

Address

Room 302, Binke Mansion, No. 1503, Xipu Road, Binjiang District, Hangzhou Zhejiang 310053

Country

China

Phone

86 571 28180555

View All Listings by this Company

Manufacturer:

Jiangxi Avonflow Hvac Tech Co., Ltd

Company Name

Jiangxi Avonflow Hvac Tech Co., Ltd

Address

No.97, Xingye Avenue, Economic Development Zone, Shangrao City Jiangxi Province

Country

China

View All Listings by this Company

Electric instantaneous, vented, mains water heater. Maximum operating temperature 98°C. Cold supply only.

Section:

1365 Heaters

Section Subtitle:

Electric instantaneous, open outlet, mains fed.

WRAS Approval Number:

250604707

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

Ellsi, model, technical data on adhesive label on body.

Installation Requirements:

R001 R040

Expiry date:

30/06/2030

Model:

PDT-000930.

Approval Holder:

Ellsi Limited

Company Name

Ellsi Limited

Postcode

DN15 8SL

Country

United Kingdom

General Email

martin@ellsi.co.uk

View All Listings by this Company

Range of under counter electric instantaneous water heaters with stainless steel tank and heating element. Open outlet use only. Maximum operating temperature 98°C.

Section:

1365 Heaters

Section Subtitle:

Electric instantaneous, open outlet, mains fed.

WRAS Approval Number:

250604712

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

DAOMENG logo printed on front panel. DAOMENG logo; Pressure, Capacity, Model No and product info on data label.

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

DM001, 241450, S2, S5.

Approval Holder:

GUANGDONG DM INTELLIGENT TECHNOLOGY CO.LTD

Company Name

GUANGDONG DM INTELLIGENT TECHNOLOGY CO.LTD

Address

17, B Building He Sui Industrial Avenue Dongheping Village Dongfeng Town Zhongshan City. Guangdong Province.

Country

China

Phone

18676009191

General Email

18666151668@163.com

View All Listings by this Company

Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. Some models, please refer to model below, incorporate only a primary circuit. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 60°C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

250602716

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Marking:

Warmhaus on front panel. Warmhaus, product name and operating info on label on side panel

Installation Requirements:

R001 R140 R360

Expiry date:

30/06/2030

Model:

Following models are ¾” BSP M inlet/outlet primary circuit, ½” BSP M inlet/outlet secondary circuit. KM0725250101005901 EWA 2525C 25KW KM0725300101005901 EWA 2530 C 30 KW KM0725310303008701 MINERWA 25/31 COMBI BOILER IE (BLACK) KM0725300201008901 ENERWA PLUS 2530 C - UK KM0325300201001301 ENERWA PLUS 2530 C - UK + FLUE KIT KM0730350201008901 ENERWA PLUS 3035 C - UK KM0330350201001301 ENERWA PLUS 3035 C + F.KIT - DHW 35 - UK KM0735400201008901 ENERWA PLUS 3540 C - UK KM0335400201001301 ENERWA PLUS 3540 C - UK KOMBI KM0742400201001301 ENERWA PLUS 4240 C 40 KW - UK KM0745430201001301 ENERWA PLUS 4543 C 43 KW - UK KM0725310303009801 EXP.MINERWA 25 SYSTEM BOLER (BLACK) KM1220240101012201 GLOWA 2024 KM1224260101012201 GLOWA 2426 KM1228300101012201 GLOWA 2830 KM1233350101012201 GLOWA 3335 KM1220240101012401 GLOWA SMART 20/24 20KW KM1224260101012401 GLOWA SMART 24/26 24KW KM1228300101012401 GLOWA SMART 28/30 28KW KM1233350101012401 GLOWA SMART 33/35 33KW Following models are ¾” BSP M inlet/outlet and are primary circuit only KM1024000201005501 EXP.ENERWA PLUS H.O 2500H KM1024000201010201 EXP. WARMHAUS ENERWA PLUS H.O 2500H - UK KM1028000201005501 EXP.WARMHAUS ENERWA PLUS H.O 3000H KM1028000201010201 EXP.WARMHAUS ENERWA PLUS H.O 3000H - UK KM1033000201005501 EXP.WARMHAUS ENERWA PLUS H.O 3500H KM1033000201010201 EXP.WARMHAUS ENERWA PLUS H.O 3500H - UK KM1133000201005501 EXP.WARMHAUS ENERWA PLUS H.O 3500H+F.KIT KM1133000201006201 EXP.WARMHAUS ENERWAPLUS HO 3500H-D+F.KIT KM1142000201005501 ENERWA PLUS H.O 4200H KM1145000201005501 ENERWA PLUS H.O 4500H KM1220000101012301 GLOWA 20 H.O. KM1224000101012301 GLOWA 24 H.O. KM1228000101012301 GLOWA 28 H.O. KM1233000101012301 GLOWA 33 H.O.

Manufacturer:

Warmhaus Isitma VE Sogutma Sistemleri Sanayi Ticaret A.S.

Company Name

Warmhaus Isitma VE Sogutma Sistemleri Sanayi Ticaret A.S.

Address

Nilufer Organise Sanayi Bolgesi Selvi Cad No:3 Nilufer Bursa Turkey

Phone

+90-224-2959400

View All Listings by this Company

Range of water meters with brass and plastic bodies and plastic turbines. The inlet incorporates a plastic filter Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” to 2 ½” BSP M (G models) DN 50 flanged (FL Models)

Marking:

Zenner logo, Model, ZR, CE, date of manufacture (YYYY) and other information on faceplate. Flow arrow and date of manufacture (YYYY) on body.

Installation Requirements:

R001 R008

Expiry date:

30/06/2030

Model:

145118 MTKD-M 2,5-165-G ¾ B (½) 144835 MTKD-M 4-190-G 1 B (¾) 145132 MTKD-M 6,3-260-G 1 ¼ B (1) 144837 MTKD-M 10-260-G 1 ¼ B (1) 145115 MTKD-M 10-260-G 1 ½ B (5/4) 145117 MTKD-M 16-300-G 2 B (6/4) 174240 MTKD-M 25-270-G 2 ½ B (2) 145446 MTKD-M 25-300- G 2 ½ B (2) 145448 MTKD-M 25-270-FL 145447 MTKD-M 25-300-FL 134886 MTKD-L-M 2,5-165-G ¾ B (½) 147662 MTKD-L-M 4-190-G 1 B (¾)

Manufacturer:

Zenner International Gmbh & Co. KG

Company Name

Zenner International Gmbh & Co. KG

Address

Heinrich‐Barth‐Str. 29, 66115 Saarbrücken, Germany

Country

Germany

View All Listings by this Company

Range of flow meters with plastic bodies. Maximum working pressure 8.0 bar Maximum operating temperature 40°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/8” BSP (F) x 3/8” BSP (M)

Marking:

BWT Logo on LCD display. Digmesa and flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

812486 (930-0074) Aquameter 3/8” with Relais. 812185 (938-A930/LE5117) Aquameter 3/8” with LCD Display. 812495 (938-A70/LE5113) Aquameter HF 3/8” with LCD Display.

Approval Holder:

BWT Holding GmbH

Company Name

BWT Holding GmbH

Address

Walter-Simmer-Straße 4 Mondsee

Postcode

5310

Country

Austria

Phone

+436648172152

General Email

andreas.stiegler@aidu.solutions

View All Listings by this Company

Range of bidet spray kits, wall outlet and brackets with brass bodies (various finishes), bidet spray kits consist of a wall outlet bracket, double interlocking flexible hose and a handset with self-closing trigger mechanism. Maximum working pressure 5 Bar. Maximum operating temperature 60°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP M

Marking:

Bidet Spray Kits: Samuel Heath logo on handset. Samuel Heath logo, WRAS and date on manufacture (YYYY) on conical nut. Samuel Heath logo on wall elbow body. Wall Outlet and Bracket: Samuel Heath logo on body

Installation Requirements:

R001 R090 R415

Expiry date:

30/06/2030

Model:

Bidet Spray Kits V159-SPR-XX V266-SPR-XX V666-SPR-XX V766F-SPR-XX V766K-SPR-XX T166-SPR-XX Wall Outlet and Brackets V159-XX V266-XX V666-XX V766F-XX V766K-XX T166-XX Where the product code suffix ‘XX’ denotes the surface finish. It will always be 2 or 3 digits, which can be any combination of numbers and/or letters. CP = Chrome plate, PN = Polished nickel, SSF = Stainless steel finish, NL = Non-lacquered, BG = Brushed gold, BGG = Brushed gold gloss lacquered, BGM = Brushed gold matt lacquered, CTB = City bronze, CNB = Country bronze, AG = Antique gold, MBC = Matt black chrome, SSB = Stainless steel finish, URB = Urban brass & URM = Urban brass matt ANT = Anthracite, OBM = Old Brass Matt, AMR = Amber Brass, ABG = Antique Brass Gloss, ABM = Antique Brass Matt

Manufacturer:

Samuel Heath & Sons Plc

Company Name

Samuel Heath & Sons Plc

Address

100 Leopold Street Birmingham

Postcode

B12 0UJ

Country

United Kingdom

Phone

+44 (0) 1217 662 200

View All Listings by this Company

Range of (chrome plated) plastic shower handsets, each supplied with five (optional) plastic flow regulators (x2 blue, light green, dark green and grey). Maximum operating temperature 60°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250115016

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Open outlet use only.

Size:

½” BSP (M).

Marking:

Inta logo on body

Installation Requirements:

R001 R040

Expiry date:

31/01/2030

Model:

HS1007CP IX100007XX IX100008XX IX100009XX

Approval Holder:

Intatec Limited

Company Name

Intatec Limited

Address

Airfield Industrial Estate Hixon Staffordshire

Postcode

ST18 0PF

Country

United Kingdom

Phone

01889272180

General Email

ryan.tilsley@intatec.co.uk

View All Listings by this Company

Range of overhead shower outlets (ABS plastic - various finishes), incorporating a stainless-steel strainer. Open outlet use only Maximum operating temperature 60.0°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250602011

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2” BSP (F)

Marking:

Villeroy & Boch on side of body

Installation Requirements:

R001 R040

Expiry date:

30/06/2030

Model:

A957328xx Where xx denotes the finish, and can be replaced with either of the following: AA – Chrome XG – Silk Black

Approval Holder:

Villeroy & Boch AG

Company Name

Villeroy & Boch AG

Address

Saaruferstraße 1-3 Mettlach

Postcode

66693

Country

Germany

Phone

+49 151 16775778

General Email

Finkler.Marc@villeroy-boch.com

View All Listings by this Company