Directory Search Results

Print List

#2203314

Range of water meter manifolds with gun metal bodies and ball valve with either a quarter turn stop valve or screw down stop valve. The products incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.

Section:
1510 Water Meter Manifolds
WRAS Approval Number:
2203314
Note:
R008 applies to te plastic cap
Size:
see model
Marking:
Ebco logo, flow arrow, Foundry I.D. (QL) & date of manufacturer (MM/YY) on body.
Installation Requirements:
R001 R008
Expiry date:
31/03/2027
Model:
1" BSP (M) x ¾” BSP (F) models: MB1030403BM MB1030403EM MANI0461V MANI0461VW MANI0461VMCP20 MVB0250MCP40 MVB0240 MVB0241 MVB0250 MVB0255 ¾ BSP (F) x ¾” BSP (F) models: MBB0460V MBB0470V MBB0461V MBB0481V MBB0040V MBB0060V MVB0210 MVB0200 MVB0220 ¾” BSP (M) x ¾” BSP (M) models: MVB0020 MVB0030 MVB0040 MVB0045 1" BSP (M) x 1” BSP (M) MVB0230
Product Images

Approval Holder:
Atlantic Plastics Ltd.
Company Name
Atlantic Plastics Ltd.
Address
Coytraherne Close, Brackla, Bridgend
Postcode
CF31 2AX
Country
United Kingdom
Phone
01656672628
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd.
Company Name
Atlantic Plastics Ltd.
Address
Coytraherne Close, Brackla, Bridgend
Postcode
CF31 2AX
Country
United Kingdom
Phone
01656672628
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2203303

Range of three or four-hole single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Four hole models Incorporate quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to a shower outlet.. Three hole models Incorporate a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided PEX lined hose assemblies. The product is supplied with a shower hose and shower handset. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.

Section:
1530 Miscellaneous Fittings
Size:
15mm compression.
Marking:
DTC53 on rear of the body. Methven on body.
Installation Requirements:
R001 R006 R007 R030
Expiry date:
31/03/2027
Model:
3 Hole models: MT3BSMCP MT3BSMBK MT3BSMBB MT3BSMBN MT3BSMGM 4 hole models: MT4BSMCP MT4BSMBK MT4BSMBB MT4BSMBN MT4BSMGM
Product Images

Approval Holder:
Methven UK Limited
Company Name
Methven UK Limited
Address
3-3A Stone Cross Court Yew Tree Way Golborne Warrington
Postcode
WA3 3JE
Country
United Kingdom
Phone
0800 195 1602
General Email
raluca.olariu@uk.methven.com

View All Listings by this Company

Print This Approval


#2203306

Range of concealed thermostatic mixing valves with DZR brass bodies incorporating a thermostatic cartridge controlling the temperature. The inlets incorporate asingle check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
1530 Miscellaneous Fittings
WRAS Approval Number:
2203306
Note:
Shower hose and shower handset are not part of this approval
Size:
¾” BSP (F)
Marking:
FM Mattsson, DR and model number on body.
Installation Requirements:
R001 R010 R040
Expiry date:
31/03/2027
Model:
51939120 51939121 51939122 51939123 51909008
Product Images

Approval Holder:
FM Mattsson Mora Group AB
Company Name
FM Mattsson Mora Group AB
Address

View All Listings by this Company
Manufacturer:
FM Mattsson Mora Group AB
Company Name
FM Mattsson Mora Group AB
Address

View All Listings by this Company

Print This Approval


#2203331

Permanent filling/ pressurisation device for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. In the event of a fall in system pressure, and only if the mains pressure is adequate, a solenoid valve operates to allow water into the system. At all other times a second solenoid valve drains the fill chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Maximum working pressure 6.0 Bar. Cold water use only.

Section:
1530 Miscellaneous Fittings
WRAS Approval Number:
2203331
Note:
Suitable for backflow protection up to fluid category 3. Consult your water supplier prior to installation
Size:
½” BSP (M)
Marking:
Flamco on front case.
Installation Requirements:
R001
Expiry date:
31/03/2027
Model:
Flexfiller Direct G4.
Product Images

Approval Holder:
Flamco Limited
Company Name
Flamco Limited
Address
Washway Lane, St. Helens
Postcode
WA10 6PB
Phone
+44 (0) 1744 744 744
General Email
info@flamco.co.uk

View All Listings by this Company
Manufacturer:
Flamco Limited
Company Name
Flamco Limited
Address
Washway Lane, St. Helens
Postcode
WA10 6PB
Phone
+44 (0) 1744 744 744
General Email
info@flamco.co.uk

View All Listings by this Company

Print This Approval


#2204042

Range of pressure transmitters with stainless steel bodies. Maximum working pressure 10.0 to 200.0 bar (please refer to model). Maximum operating temperature 100°C.

Section:
1530 Miscellaneous Fittings
Size:
1/2 in - 14 NPT female 1/2 in - 14 NPT male / 1/4 in - 18 NPT female DIN EN 837-1 G 1/2 B Front bonded G 1/2 in
Marking:
ABB, model, serial number & technical info on adhesive label on body.
Installation Requirements:
R001
Expiry date:
30/04/2027
Model:
PAS100.X.Y.GW/GA & PGS100.X.Y.GW/GA Where X denotes the pressure and can be replaced with any of the following sensor range (and max working pressure): C = 60 mbar (10.0 bar). F = 400 mbar (10.0 bar). L = 2500 mbar (30.0 bar). D = 10 bar (60.0 bar). K = 40 bar (80.0 bar). R = 100 bar (200.0 bar). Where Y denotes the connections and can be replaced with any of the following: A = 1/2 in - 14 NPT female B = 1/2 in - 14 NPT male / 1/4 in - 18 NPT female C = DIN EN 837-1 G 1/2 B P = Front bonded G 1/2 in
Product Images

Approval Holder:
ABB S.p.A
Company Name
ABB S.p.A
Address
Via Vaccani, 4 Tremezzina (loc. Ossuccio)
Postcode
22016
Country
Italy
General Email
matteo.gaffuri@it.abb.com

View All Listings by this Company
Manufacturer:
ABB S.p.A
Company Name
ABB S.p.A
Address
Via Vaccani, 4 Tremezzina (loc. Ossuccio)
Postcode
22016
Country
Italy
General Email
matteo.gaffuri@it.abb.com

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 397 of 1707

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.