'Belzona 5811DW2 (grey)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (grey, opaque glossy paste) with Part B (orange, transparent liquid) in a 4:1 mass ratio and apply as per manufacturer’s IFU ’16-03-19’. Cure for 4 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

250855036

Expiry date:

31/08/2030

Approval Holder:

Belzona Limited

Company Name

Belzona Limited

Address

Claro Road, Harrogate, Yorks.

Postcode

HG1 4AY

Phone

+44 1423 567641 Fax: 01423 505967

View All Listings by this Company

Tecomid NA40 GR25 NL HS QF (white coloured) and Tecomid NG40 GR30 BK250 HS QW, Tecomid NA40 GR30 BK005 HY QH & Tecomid NA40 GR30 BK250 HY QW (black coloured). Injection moulded PA materials. Tecomid NA40 GR25 NL HS QF (white coloured) & Tecomid NG40 GR30 BK250 HS QW (black coloured) are suitable for use with water up to 85°C. Tecomid NA40 GR30 BK005 HY QH (black coloured) & Tecomid NA40 GR30 BK250 HY QW (black coloured) are suitable for use with water up to 23°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

250755050

Expiry date:

31/07/2030

Approval Holder:

Eurotec Muhendislik Plastikleri San. ve Tic. A.S.

Company Name

Eurotec Muhendislik Plastikleri San. ve Tic. A.S.

Address

Karamehmet Mah. Avrupa Serbest Bolgesi, Avrasya Bulvari No: 8, TR 59930 Ergene

Country

Turkey

View All Listings by this Company

'XS10B & XRC30B'. Black coloured, extruded, Polyethylene materials. For use with water up to 23°C.

Section:

5245 Polyethylene

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

250755058

Expiry date:

31/07/2030

Approval Holder:

Hanwha Total Petrochemical

Company Name

Hanwha Total Petrochemical

Address

103, Dokgot2-Ro, Daesan-Eup, Seosan-Si, ChungNam, 31900

Country

Korea, Republic of

View All Listings by this Company

'Tecoflex TU40 GR30 GR128 HS D6 QF'. Light grey coloured, injection moulded TPU material. For use with water up to 23°C.

Section:

5297 Polyurethane

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

250755049

Expiry date:

31/07/2030

Approval Holder:

Eurotec Muhendislik Plastikleri San. ve Tic. A.S.

Company Name

Eurotec Muhendislik Plastikleri San. ve Tic. A.S.

Address

Karamehmet Mah. Avrupa Serbest Bolgesi, Avrasya Bulvari No: 8, TR 59930 Ergene

Country

Turkey

View All Listings by this Company

Section:

0531 Combination Tap Assemblies

Description:

A Two hole tap(s) with a single outlet and a fixed spout, incorporating a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3)

Deck mounted. Capable of achieving AUK2 Tap gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R005 R030

Expiry date:

31/01/2031

Notes & Further Information

X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1

Product Images

Approval Holder:

PPI Xiamen Industry Co., Ltd.

Company Name

PPI Xiamen Industry Co., Ltd.

Address

No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen

Postcode

361022

Country

China

General Email

heatheryang@xmppi.com

View All Listings by this Company

Manufacturers:

PPI XIAMEN INDUSTRY CO LTD