Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coated ductile iron bodies and hand wheel operating members. Maximum working pressure 25.0 bar (DN50-DN300) or 10.0 bar (DN400 only) Maximum operating temperature 85ºC
AMEXSA range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of in-line pilot operated control valves with blue epoxy coated ductile iron bodies, having rate of flow control facility controlled via a pilot system. Spring ratings of pilot valve are 2 to 20 psi / 0.138 to 1.38 bar, 25 to 50 psi / 1.72 to 3.4 bar. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of push-fit, screw down stop valves with plastic bodies for use with copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS 7291-3) and/or MDPE pipe (manufactured to EN 12201 (inserts required). For above and below ground use. Maximum working pressure:16.0 bar Maximum operating temperature: 20.0°C.
Range of inlet control groups with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve set to 6bar. The outlet incorporates a single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2. Pressure reducing range 1 bar to 6 bar Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
'Polyplumb' (grey coloured) & 'Polyfit' (white coloured) fittings. Injection moulded acetal fittings. For use with water up to 65°C.
'LM119-1'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no.: LM-001', 'Edition: A', 'Issue date: 2024-JAN.-15th'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZHR‐SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2025.8.27'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Ecocoat FBE Green Powder PFC/6018 (RAL 6018)& Ecocoat FBE Red Oxide Powder PFC/3000-Red Oxide'. Factory applied, green or red coloured epoxy coatings. Apply as per manufacturer’s Product Data Sheet revised ‘1st Jan, 2024’. Cure for 3 minutes at a metal temperature of 230°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Eurokote® 48-20 Brun Rouge’. Factory applied, red coloured, two-part epoxy coating. ‘Eurokote® 48-20 Ivoirine’ was added to the approval in March 2026. Factory applied, white coloured, two-part epoxy coating. Mix resin and hardener in a 2.13:1 mass ratio and apply as manufacturer's TDS dated '10/12/2024'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Silicone Grease WA'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Proofex HDPE B125'. White coloured, extruded HDPE waterproofing membrane. For use with water up to 60°C.
'Netbor HDPE Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 65°C.
'Brothers Polyproplene fittings'. Blue coloured, injection moulded PP fittings. For use with water up to 65°C.
Page 384 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
