Directory Search Results

Print List

#2111311

Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The supplies to both domestic hot water and primary are controlled via spherical valves. The primary circuit has a maximum working pressure of 2.5 bar. The secondary circuit has maximum working pressure of 10.0 bar. Maximum supply temperature is 60°C. Maximum operating temperature of secondary circuit is 85°C.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
2111311
Size:
Primary: 22mm compression inlet/outlet. Secondary: 15mm compression.
Marking:
Worcester and Worcester logo on front of boiler.
Installation Requirements:
R001
Expiry date:
30/11/2026
Model:
7-733-600-371: Greenstar 4000 25 Combi NG. 7-733-600-372: Greenstar 4000 25 Combi LPG. 7-733-600-373: Greenstar 4000 30 Combi NG. 7-733-600-374: Greenstar 4000 30 Combi LPG.

Approval Holder:
Worcester Bosch
Company Name
Worcester Bosch
Address
Cotswold Way Warndon Worcester
Postcode
WR4 9SW
Country
United Kingdom
Phone
+44 1905 752761
General Email
ian.sharp@uk.bosch.com

View All Listings by this Company
Manufacturer:
Bosch Thermotechnology Ltd. Bosch Thermotechnik GmbH. Bosck Termoteknik Sanayu ve Ticaret A.S.
Company Name
Bosch Thermotechnology Ltd. Bosch Thermotechnik GmbH. Bosck Termoteknik Sanayu ve Ticaret A.S.
Address
General Email

View All Listings by this Company

Print This Approval


#2112354

Range of gas fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The cold inlet incorporates an angled spherical valve with a brass body, chromium plated brass ball and a lever operating member. The primary circuit incorporates an expansion vessel, isolation valves on flow and return, drain valve and a pressure relief valve set at 3.0 bar. Maximum working pressure of the primary circuit is 2.5 bar. Maximum working pressure of the secondary circuit is 10.0 bar. Maximum operating temperature for the secondary circuit is 55˚C. Cold supply only.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
2112354
Size:
Secondary: 15mm copper tail. Primary: 22mm copper tail.
Marking:
Biasi and Biasi logo on front panel. Biasi, Biasi logo, pressure, model and other technical information on label on inside cover.
Installation Requirements:
R001 R140 R360
Expiry date:
31/12/2026
Model:
Advance Plus 25C ERP, Advance Plus 30C ERP, Advance Plus 35C ERP, M300V.2025 SM, M300V.2530 SM, M300V.3035 SM, M275V.2024 SM, M275V.2428 SM, M275V.2832 SM.

Approval Holder:
BSG Caldaie a gas S.p.A.
Company Name
BSG Caldaie a gas S.p.A.
Address
Via Pravolton 1/b Pordenone
Postcode
33170
Country
Italy
Phone
+39 0434 238311
General Email
luca_norio@bsgspa.it

View All Listings by this Company

Print This Approval


#2111364

Greenstar Heatslave II range of floor standing oil-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system, which incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The cold water inlet incorporates a screwdriver operated spherical valve followed by a plastic flow regulator inserted within the pipework. Maximum working pressure: Primary circuit 2.5 bar. Secondary circuit 10.0 bar. Maximum operating temperature 82°C.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
2111364
Note:
Not supplied with a temporary filling loop. A filling loop must be installed with the appropriate backflow prevention device in accordance with clause G24.2, Guidance to the Water Supply (Water Fittings) Regulations 1999. R430 applies to the EXT models only.
Size:
Primary: 28mm copper tail (25/32 models), 22mm copper tail (all other models). Secondary: 15mm inlet x 22mm copper tail outlet.
Marking:
Worcester (brand of Bosch Thermotechnology Ltd) and Worcester logo on front casing. Data label, Worcester and technical information on inside cover.
Installation Requirements:
R001 R140 R360 R430
Expiry date:
30/11/2026
Model:
7 731 600 165 Greenstar Heatslave II 12/18 ErP+, 7 731 600 166 Greenstar Heatslave II 18/25 ErP+, 7 731 600 167 Greenstar Heatslave II 25/32 ErP+, 7 731 600 168 Greenstar Heatslave II EXT 12/18 ErP+, 7 731 600 169 Greenstar Heatslave II EXT 18/25 ErP+, 7 731 600 170 Greenstar Heatslave II EXT 25/32 ErP+, 7 731 600 260 Greenstar Heatslave II 12/18 2022+, 7 731 600 261 Greenstar Heatslave II 18/25 2022+, 7 731 600 262 Greenstar Heatslave II 25/32 2022+, 7 731 600 263 Greenstar Heatslave II EXT 12/18 2022+, 7 731 600 264 Greenstar Heatslave II EXT 18/25 2022+, 7 731 600 265 Greenstar Heatslave II EXT 25/32 2022+.

Approval Holder:
Worcester Bosch
Company Name
Worcester Bosch
Address
Cotswold Way Warndon Worcester
Postcode
WR4 9SW
Country
United Kingdom
Phone
+44 1905 752761
General Email
ian.sharp@uk.bosch.com

View All Listings by this Company
Manufacturer:
Bosch Thermotechnology Ltd.
Company Name
Bosch Thermotechnology Ltd.
Address
Danesmoor Works Pilsley Clay Cross Chesterfield Derbyshire
Postcode
S45 9BY
General Email

View All Listings by this Company

Print This Approval


#2110331

Range of air cooled ice making machines . Inlet is controlled via solenoid valve. Maximum working pressure 5.5 bar. Cold water use only.

Section:
1500 Ice Making Machine(s)
Size:
See model.
Marking:
Manitowoc logo on door. Manitowoc, model, serial number & technical information on body.
Installation Requirements:
R001 R009 R160 R171 R511
Expiry date:
31/10/2026
Model:
I(*)T0300A I(*)T0300W I(*)P0320A I(*)T0420A I(*)T0450A I(*)T0450W I(*)T0500A I(*)P0500A I(*)T0620A I(*)T0620W I(*)T0750A I(*)T0750W I(*)T0900A I(*)T0900W I(*)T1200A I(*)T1200W I(*)T1200N IBT1020C I(*)T1500A I(*)T1500W I(*)T1500N I(*)T1900A I(*)T1900N I indicates Indigo family of Ice Machines (*) Indicates D, Y or R. Dependent on ice cube size (T or P) Indicates refrigerant type (T=R410A, P=R290) 4 numerical characters indicate to icemaking capacity per 24hrs Final character indicates cooling option (A=Air, W=Water, N=Remote Condenser, C=Remote Condensing Unit)
Models added July 2024: I(*)P0300A I(*)P0420A I(*)P0620A I(*)P0620W I(*)P0600A I(*)P0600W I(*)P0900A I(*)P0900W I(*)P1200A I(*)P1200W I(*)P1200N I(*)P1500A I(*)P1500W I(*)P1500N I(*)P1900A I(*)P1900N

Approval Holder:
Pentair Commercial Ice LLC
Company Name
Pentair Commercial Ice LLC
Address
5500 Wayzata Blvd. Suite 900 Golden Valley, MN
Postcode
55416
Country
United States
General Email
jeng.yang@pentair.com

View All Listings by this Company
Manufacturer:
Pentair Commercial Ice LLC
Company Name
Pentair Commercial Ice LLC
Address
5500 Wayzata Blvd. Suite 900 Golden Valley, MN
Postcode
55416
Country
United States
General Email
jeng.yang@pentair.com

View All Listings by this Company

Print This Approval


#2111023

‘Aquila V4 C1’ range of water meters (brass or bronze bodies) with a plastic working chamber, flow regulator and impellor, and either NBR or EPDM ‘O’-rings. The products are supplied with loose NBR/fibre flange gaskets. Maximum working pressure 16.0 bar. Cold water use only.

Section:
1505 Water Meters
Size:
DN50 - DN100 flanged
Marking:
DIEHL logo on cap. DIEHL METERING, CE, temperature, maximum pressure and other technical information on meter face. Flow arrow and size on body
Installation Requirements:
R001
Expiry date:
30/11/2026
Model:
Aquila V4 C1: Brass bodies: DN 50 and DN 65 length 300 mm Bronze bodies: DN 80 and DN 100 length 350 mm

Approval Holder:
Diehl Metering S.A.S & Diehl Metering Sp. Z o.o.
Company Name
Diehl Metering S.A.S & Diehl Metering Sp. Z o.o.
Country

View All Listings by this Company
Manufacturer:
Diehl Metering S.A.S & Diehl Metering Sp. Z o.o.
Company Name
Diehl Metering S.A.S & Diehl Metering Sp. Z o.o.
Country

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 39 of 451

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.