Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
‘KBGR16’ range of gate valves with either brass or DZR brass bodies and PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. DN50 to DN500 sizes are operated by handwheel. DN600 to DN800 sizes are operated by a gear box. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with ductile iron bodies (blue epoxy powder coated) incorporating EPDM encapsulated Wedge and bonnet with EPDM `O` rings and gaskets. Valves incorporate handwheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C
Range of gate valves with brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Magnetic scale reducer, incorporating chrome plated copper body, for use with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line electrolytic scale reducers with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
'CY103'. Dark grey coloured, cold pressed, phenolic resin impregnated carbon graphite seal ring. For use with water up to 85°C.
'FH821Z2'. Dark grey coloured, pressed & carbonised, resin impregnated carbon bearing. For use with water up to 85°C.
'KH369AC'. Dark grey coloured, compression moulded carbon/graphite ring. For use with water up to 85°C.
'NM 96 & NM 99 Ceramic Discs'. Off-white coloured, compression moulded ceramic discs. For use with water up to 85°C.
‘Rashmi Portland Slag Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/003', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/005', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AF-GL®'. Grey coloured NBR/fibre gasket material manufactured by calendaring. For use with water up to 85°C.
'Burasil Universal 9544/U'. Green coloured NBR/fibre gasket material manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'AF-300 B Pro'. Blue coloured, NBR/fibre gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio
'Tesnit® BA-GL & Tesnit® BA-GL3000'. Green/blue coloured fibre gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Greasil 4000'. White coloured silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
Page 360 of 393
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
