'C21 Dyopox PTW White'. Factory applied, two-part, creamy white coloured epoxy resin coating. Mix base and hardener in a mass ratio of 4:1 and apply as per manufacturer's TDS dated '2011'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Klubertop TP 38-901’. Site applied, (transparent) white coloured PTFE lubricant coating. Apply and cure as per Kluber Lubrication product information sheet ‘Prod. 099030, en-GB, Edition 12.05.2022’. For use with water up to 85°C.
'68093X'. Factory applied, blue coloured epoxy powder coating. Apply per manufacturer's instructions 'V2.3' dated March 2018. Cure for 20 minutes@200°C For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kinlin Epoxy Power Coating (Green colour, EPX‐111A)'. Factory applied, green coloured epoxy powder coating. Apply as per manufacturer's instructions 'XL-R-019-G1' dated '2018-9-21'. Cure for 10 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TEADIT NA1005'. Blue coloured, compressed non-asbestos NBR fibre gasket material manufactured by calendaring. For use with water up to 23°C.
'Tecnoplast GRVE pipe'. Translucent, light green coloured, GRP pipe manufactured by hand lay-up. For use with water up to 23°C. From July 2024 the pipe is for use with water up to 60°C.
'KORASILON® Paste hochviskos' & 'KORASILON® Paste M-S 2-200'. White coloured (translucent) lubricants. Apply as per manufacturer's Product Data Sheet '30.01.2023'. For use with water up to 85°C.
'Pexgol Pipe'. White coloured (transcluent), extruded PE-Xa pipe. For use with water up to 70°C.
'PPA-GF10-NC' (natural, appears yellow-green) & 'PPA-GF10-BK' (black coloured). Injection moulded PPA materials. For use with water up to 85°C.
'KTP Thermopipes'. Green coloured, extruded PPR pipe. For use with water up to 70°C.
'122102251 PP Mechanical Fitting'. Black coloured, injection moulded, polypropylene compression fitting body. For use with water up to 23°C.
'RRS 502B GR1500'. In February 2025, ‘RRA 410B GR1500’ was added to the approval. Dark grey coloured, injection moulded PVC materials. For use with water up to 23°C.
'01/U80EP'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 80. Tested in-radii sizes between 1.00mm & 2.5mm. For use with water up to 85°C.
'EP7/3/7 BLK O-rings & gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 75. The gaskets have an in-radius size of 1.0mm. The 'O' rings have an in-radius size of 1.3mm. For use with water up to 85°C.
'EP70 BLK Seals'. Black coloured, injection moulded EPDM seals. Shore hardness 70. Tested in-radius size 1.0mm. In April 2024, 'EP70 BLK 'O' rings’, black coloured, injection moulded 'O' rings were added to the approval. Shore hardness 70. Tested in-radius size of 1.3mm For use with water up to 85°C.
'HH7118F 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'334137 – EPDM Peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'PT0469'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EP002971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7001165PWRC'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 344 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
