'POLIMID A SG NATURALE WR'. Natural (appears white in colour), injection moulded PA 66 material. In February 2025 'POLIMID A SG BLACK WR-PA66', black coloured, injection moulded PA 66 material was added to the approval. For use with water up to 85°C.
'Magnetic Rotor, 011201_02_02'. Black coloured, injection moulded nylon magnet rotor component. For use with water up to 85°C.
'POLYWORK® H2G50DW NC' (appears off-white) & 'POLYWORK® H2G50DW BK' (black coloured). Injection moulded glass fibre reinforced PA66+PA6I/6T materials. For use with water up to 85°C.
'DFC White HDPE Float 025RBX006HP'. White coloured, extruded and machined HDPE float component. For use with water up to 65°C.
'BWRB1620200'. In July 2024 the following pipes were added to the approval: ‘BWRB1620100, BWRB2020200, BTRB2525100 & BTRB3230100. Triple layered, extruded pipes consisting of an off-white coloured PERT inner layer, aluminium middle layer and white coloured PERT outer layer. For use with water up to 85°C.
'Borstar® RA150E'. Natural (appears off-white) polypropylene material for injection moulding and extrusion purposes. For use with water up to 85°C.
'Topilene R202P'. White coloured, extruded polypropylene material. For use with water up to 85°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 04/06/218. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'vinyl eco/EASF'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 25/09/2017. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CH200'. Brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'version 24/05/2018'. Cure for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Chemfix CH+ MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 18/05/2022. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPDM 70.502-03 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.
`SW EPDM`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'AquaFlex T 5857'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 70°C.
‘ME0996’ components. Black coloured, injection moulded NBR rubber components. ‘O’-rings with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. Between November 2023 and April 2024, the approval included gaskets with an in-radius size of 5.0mm. Shore hardness 40. From May 2024 the gasket range was extended to include gaskets with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. For use with water up to 23°C.
'NB7041F'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'Griffon UNI-100 XT'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6300427', issue '1'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 336 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
