'PPA571ES Black 700 & PPA571 Black 700'. Factory applied Polyolefin PE Coatings. Apply 'PPA571 Black 700' by fluidised bed according to manufacturer's data sheet '08/2022' and dip in the bed for 5-8 seconds. Apply 'PPA571ES Black 700' by electrostatic spray according to manufacturer's data sheet '08/2022'. Cure for 190-200°C for 20 mins. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL035P Interpon 100 Gloss Light Grey'. Factory applied, light grey coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'Interpon 100 -AL035P - Issue #01', revision date '20.07.2021'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'CY7000 Blue'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instruction manual 'YS-QNS-WZBC-2021W', dated 'May 20, 2021'. Cure for 15 minutes@180°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'C21 Dyopox PTW White'. Factory applied, two-part, creamy white coloured epoxy resin coating. Mix base and hardener in a mass ratio of 4:1 and apply as per manufacturer's TDS dated '2011'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Magnetic Rotor, 011201_02_02'. Black coloured, injection moulded nylon magnet rotor component. For use with water up to 85°C.
'POLYWORK® H2G50DW NC' (appears off-white) & 'POLYWORK® H2G50DW BK' (black coloured). Injection moulded glass fibre reinforced PA66+PA6I/6T materials. For use with water up to 85°C.
'BWRB1620200'. In July 2024 the following pipes were added to the approval: ‘BWRB1620100, BWRB2020200, BTRB2525100 & BTRB3230100. Triple layered, extruded pipes consisting of an off-white coloured PERT inner layer, aluminium middle layer and white coloured PERT outer layer. For use with water up to 85°C.
'Chemfix CH+ MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 18/05/2022. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'01/U80EP'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 80. Tested in-radii sizes between 1.00mm & 2.5mm. For use with water up to 85°C.
‘ME0996’ components. Black coloured, injection moulded NBR rubber components. ‘O’-rings with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. Between November 2023 and April 2024, the approval included gaskets with an in-radius size of 5.0mm. Shore hardness 40. From May 2024 the gasket range was extended to include gaskets with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. For use with water up to 23°C.
‘ME2020’ injection moulded components. Silicone rubber ‘O’ rings and gaskets available in red, blue, white, black, light grey colours. Shore hardness between 30 - 70. Tested in-radii sizes between 0.5mm and 5mm. For use with water up to 85°C.
‘LS40T-0301, LS50T-0301, LS60T-0301, LS70T-0301 & LS80T-0301’. Injection moulded, liquid silicone rubber sheet material, available in white, grey, black, blue, green, natural (unpigmented) & red colours. Shore hardness between 40SH-A & 80SH-A. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘Paryls® PPSU F1550NC (natural grade – appears brown), F1550GY (grey coloured), F1550BK (black coloured) & F1550WH (white coloured)’. Injection moulded PPSU materials. For use with water up to 85°C.
'POKETONE’ range of natural (appears light brown), grey and black, injection moulded Polyketone materials. For use with water up to 85°C. 'M(a)3FG(b)A-NP0, M(a)3FG(b)A-GY(c), M(a)3FG(b)A-BK(c)'. (a) indicates the MI(g/min) or viscosity of its neat resin and is replaced with: 9 = 150~250, 3 = 40~80, 6 - 4~8 or 7 = 2~4. (b) indicates the content of glass fibre and is replaced numbers between 1 & 9 (9 indicating the maximum of 50%). NP0 indicates natural material, GY indicates grey material & BK indicates black material. (c) can indicate a random product number of each grade OR the ratio of carbon black and is replaced with numbers between 0 & 9.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water supply only.
Range of single hole, single outlet, fixed, electronically controlled combination tap assemblies, (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. A stainless steel braided PEX lined flexible hose connects the components. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 45°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate a plastic aerator and flow regulator. The tap incorporates a soap dispenser with separate dispensing nozzle. Maximum working pressure 8.0 Bar. Maximum operating temperature 55°C.
Page 328 of 584
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
