Range of polyethylene pressure vessels with spun fibreglass casing. Maximum working pressure 10.0 bar Maximum operating temperature 50°C.
'GDPA PermaCoat'. Factory applied, blue coloured (once applied) coating system comprising of a Yellow Zinc Primer and Polyamide top coat. Apply one coat of Yellow Zinc as per work instructions 'PR/WI/01', revision '00', dated '22/11/2017', plating for 45 minutes@30°C. Apply one coat of top coat as per work instructions 'BR/WI/01', revision '00', dated '29/10/2010' and cure for 30 minutes@215°C. For use with water up to 23°C. This material is only approved for the plating and curing conditions that appear on the approval. If the plating and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELTEX® SUPERSTRESS TUB121N9000'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
'ECOTRAN E2130W(#) NC'. Natural (appears beige) PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E2130W(#) BK'. Black coloured PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'RAMSET ChemSet™ Reo502™ Xtrem™’ & ‘RAMSET ChemSet™ Epcon™ G5 Xtrem™'. Site applied, brick coloured (once mixed), chemical anchor resins, each supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'NOV. 25'. Cure for 24 hours@21°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fernox LS-X'. Clear, silicone sealant. Apply as per manufacturer's technical data sheet dated 10-05-2021. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 8 bar. Maximum operating temperature 60°C.
Bottom entry or side entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and a plastic flow regulator at the inlet. Maximum working pressure 10.0 Bar Cold water use
Page 309 of 320
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
