'ENDOPRENE® 851 Blanc'. Factory applied, white coloured, two-component polyurethane coating. Mix parts A & B in 50:50 volume ratio and apply as per manufacturer's TDS dated 10/07/2024. Cure for 6 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'175-767 Polyester blue 5012'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions updated '15.03.2018'. Cure for 10 minutes@180°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Series 2000 RAL 5015'. Factory applied, blue coloured epoxy resin coating. Apply as per manufacturer’s data application sheet ‘Revision: 6 (2018/10/01)’ created ‘2015/11/11’. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MJ-6'. Factory applied, blue coloured epoxy resin powder coating. Mix in a 63%/21.8%/13.2%/2% ratio and apply as per manufacturers instructions 'v1', dated '06-05-2023'. Cure for 60 minutes@200°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘NMSP2104 M & ER2104A01SM'. The following coatings were added to the approval in March 2025: ER2209A01SC, ER2252A01SC, ER2259A01SC & ER2260A01SC. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 38', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PMSP5099-M & EP5099D01SC'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 37', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PRIMGREEN® ENDURANCE & Primgreen LAT 12035' primers for use with 'RILSAN® PA11 T BLUE 7444 MAC (16293), PA11 T GREY 5161 MAC (17203), PA11 T WHITE 1488 AC (17219) & PA11 T BLACK 7450 AC (17185)' coatings. Factory applied primers and powder coatings. The piece to be coated is to be pre-heated to 330°C for 10 minutes, the primer and coating applied in accordance with user instructions 'Dircom - 4418E/05.2015/20' and then cured for 10 minutes@330°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'novapress®BASIC'. Orange coloured NBR/aramid fibre gasket material, manufactured by calendaring. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
‘FlatSeal™HMF10’. Orange coloured NBR/aramid fibre gasket material, manufactured by calendaring. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
'MOLYguard HVG'. Clear silicone lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Klüberbeta VR 67-3500'. Cream coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Syntheso LM 220'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'UNISILKON L 250 L'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'UNISILKON L 641'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'SAPPHIRE Endure Bearing Grease'. White coloured grease. For use with water up to 85°C.
'Turmsilon GL 320-G'. White coloured silicone grease/lubricant. For use with water up to 85°C.
'Ferrimax 35h with Parylene Coating'. Sintered ferrite magnet encapsulated in grey coloured coating. For use with water up to 85°C.
'Relon A500 Nero 4095 GF30 K'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 80°C.
'Wirsbo inPEX'. White coloured (translucent), extruded polyethylene pipe. For use with water up to 85°C.
'CP Polytec PE80E Blue Pipe'. Blue coloured, extruded PE pipe. For use with water up to 23°C.
Page 280 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
