'Polyurea FA 1044'. Factory applied, two-component, beige coloured polyurea coating. Mix parts A and B in a 1:1 volume ratio apply as per manufacturer's TDS '07/2015 Rev.00'. Cure for 96 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC1003XT'. Factory applied, green coloured fusion bonded epoxy coating. Apply as per manufacturer's TDS dated 8 June 2021. Cure for 5 minutes@235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. Resicoat R4 blue R4-FB HJC06R & R4-ES HJF26R. Resicoat R4 red/red-brown R4-ES HGF03R. Resicoat R4 black R4-FB HNC01R. Resicoat R4 black: R4-ES HNF04R.
‘PVEF undercoat with Fluiglide Topcoat’. Factory applied, cream coloured (once mixed and applied), coating system comprising of ‘Polyglass VEF’, two-component glassflake vinyl ester undercoat and ‘Fluiglide’, two-component polyester topcoat. Mix and apply ‘Polyglass VEF’ in accordance with Corrocoat ‘product reference 2/23’ dated ‘5th June 2007’ and last reviewed ‘March 2022’. Cure for 24 hrs@20°C (±1°C). Mix and apply ‘Fluiglide’ in accordance with Corrocoat ‘product reference ‘4/01’, valid from ‘23rd October 1995’ and last reviewed ‘March 2022’. Cure for a minimum of 6 days@20°C (with a lower tolerance of -1°C). These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Nitocote CM210 '. Site applied, grey coloured, two-component cementitious coating comprising of Nitocote CM210 White (base coat) and Nitocote CM210 grey (top-coat). 'Nitocote CM210 White' (base coat) consists of Part A (white coloured powder) and Part B (white coloured liquid) to be mixed in a mass ratio of 100:27.7. Cure for 4 hours@20°C. 'Nitocote CM210 grey' (top-coat) consists of Part A (grey coloured powder) and Part B (white coloured liquid) to be mixed in a mass ratio of 100:27.7. Cure for 8 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SANIBIW WB-R Reinforced Multilayer Hoses' and ‘SANIBIW WB-R Hose’. 'SANIBIW WB-R Reinforced Multilayer Hoses' are dual layered, extruded hoses, consisting of an off-white translucent (natural) silicone rubber inner layer and VMQ silicone rubber (with PES reinforcement) outer layer. The outer layer is available in black, red/brown, white or silver colours. Shore hardness 70. The inner and outer layers each have a tested in-radius size of 1.1mm. ‘SANIBIW WB-R Hose’ is a single layered, translucent (natural), extruded silicone rubber hose with PES reinforcement. Shore hardness 70. Tested in-radius size of 2.0mm. All hoses are for use with water up to 85°C.
'SANIBIW WB Hose’. Single layered, uncoloured & translucent (natural), extruded silicone rubber hose. Shore hardness 70. Tested in-radius size of 2.0mm. For use with water up to 85°C.
'IKV Tribosil MHL 40'. Clear silicone liquid lubricant. Apply as per manufacturer's technical data sheet. No cure required. For use with water up to 85°C.
'4MID 9B22130 W-A BNL100'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'Genestar™ G1500D-L47WF BLACK'. Black coloured, injection moulded or extruded Polyamide 9T material. For use with water up to 85°C.
Page 264 of 1167
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
