'AMMT-029 Waterborne Anticorrosive Coating'. Factory applied, black coloured acrylic modified resin coating. Apply as per manufacturer's Instructions for Users 'version 2.00', updated '11/01/2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monolevel 844SP'. Site applied, grey coloured, polymer modified cementitious mortar. Mix mortar with water in a weight ratio of 5:0.6. Apply as per manufacturer's instructions 'Bulletin No. ML844SP/031/010' issued July 2020. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Xypex Concentrate'. Site applied, grey coloured, cementitious coating. Mix 'Xypex Concentrate' with water in a 5:2 ratio and apply as per manufacturer's datasheet 'DAT-CON-UK, REV-06-21'. Cure for 3 days@7°C in damp conditions, following by 18 days@7°C. Please note that 1 day cure = 24 hours. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Carlow Tank Mix 1'. Factory prepared, grey coloured concrete mix. Mix and apply as per statement from ‘Carlow Concrete Tanks', dated '23rd January 2023' Cure for 7 days@21°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Grivory HT1V-5 FWA grey L2172.5'. Grey coloured, injection moulded PA6I/6T-GF50 material. For use with water up to 85°C.
‘ULTRAMID® A218W V30 Natural-C’ (natural, appears off-white) & ‘ULTRAMID® A218W V30 Black-C’ (black coloured). Injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Hifax CA 721 GW'. White translucent, injection moulded polypropylene material. For use with water up to 23°C.
'Membrane R219 34 9513 NBR 55 Sh'. Black coloured, injection moulded NBR rubber membrane. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Flomasta Liquid PTFE (SKU: 5321J)'. Blue coloured, liquid PTFE anaerobic sealant. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. Models are either cold/premixed water only or hot and cold supply with a manually adjustable temperature lever. The product incorporates stainless steel strainers and the inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Page 261 of 350
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
