A range of four-hole single outlet fixed combination tap assemblies with brass bodies in a variety of finishes (See models). Incorporating ¼ ceramic disc headworks with single lever operating members and a self-cancelling diverter to a shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet elbow incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. This product is supplied with a shower hose, shower handset and metal screw clamp type back nuts. The side valves and the spout are connected with a copper tube. Maximum working pressure 10 bar. Maximum working temperature 60 °C.

Section:

0680 Combination Tap Assemblies

Section Subtitle:

Multi hole tap(s) with a single outlet and a swivel spout , incorporating a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3).

WRAS Approval Number:

2112042

Size:

For use with basic set 13244180 which has ½” BSP (M) inlets

Marking:

HANSGROHE on Spout

Installation Requirements:

R001 R006 R030

Expiry date:

31/12/2026

Model:

HG Vernis Blend 4 hole bath mixer chrome models: 71 456 xxx 71 459 xxx Has to be installed with basic set 13 244 180 (HG 4 hole bath mixer basic set) Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Expansion vessels incorporating a stainless steel body and EPDM membrane. Maximum working pressure 10.0 bar. Maximum operating temperature 100˚C.

Section:

1000 Expansion Vessels

Size:

½” BSP (M)

Marking:

Aquasystem, model, serial No, date of manufacture (DD/MM/YYY) & other technical information on adhesive label on body.

Installation Requirements:

R001

Expiry date:

30/09/2026

Model:

XVES050005: 0.50L SHOCK ARRESTOR PRE‐SET 3.5BAR 1/2"MBSP XVES050006: 1L SHOCK ARRESTOR PRE‐SET 3.5BAR 1/2"MBSP XVES050007: 2L SHOCK ARRESTOR PRE‐SET 3.5BAR 1/2"MBSP

Approval Holder:

Reliance Worldwide Corporation (UK) Ltd

Company Name

Reliance Worldwide Corporation (UK) Ltd

Address

Horton Road, West Drayton

Postcode

UB7 8JL

Country

United Kingdom

Phone

+44 7730 052060

General Email

PETER.LANCASTER@RWC.COM

View All Listings by this Company

Range of brass tee fittings for use with copper pipe to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2112337

Size:

See model

Marking:

Aquamatic Products Limited logo (APL) on body.

Installation Requirements:

R001

Expiry date:

31/12/2026

Model:

B840-1 - 15mm compression x 15mm spigot x 15mm spigot. B841-1 - 22mm compression x 22mm spigot x 22mm spigot.

Approval Holder:

Aquamatic Products Limited

Company Name

Aquamatic Products Limited

Address

Hydestile Stud Hambeldon Road Godalming Surrey

Postcode

GU8 4DE

Country

United Kingdom

Phone

01483 861559

General Email

steve@aquamatic.co.uk

View All Listings by this Company

‘HE-705X & HE-715X’ ranges of brass crimp fit fittings incorporating EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057-2006). HE-7052/7053/7058/7059 & HE-7152/7153/7158/7159 models also incorporate a NBR gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2109058

Size:

See model

Marking:

HONGEN, WRAS and size on crimp connection.

Installation Requirements:

R001

Expiry date:

30/09/2026

Model:

M-type connection: HE-7050 - straight connector - pressfit x BSP (M): 15-54mm x ½”-2”. HE-7051 - straight connector - pressfit x BSP (F): 15-54mm x ½”-2”. HE-7052 - straight connector (with central captive nut and washer) - pressfit x BSP (F): 15-28mm x ½”-1”. HE-7053 - straight connector (with central captive nut and washer) - pressfit x pressfit: 15x15-28x28mm. HE-7054 - 90° elbow - pressfit x BSP (M): 15-28mm x ½”-1”. HE-7055 - 90° elbow - pressfit x BSP (F): 15-28mm x ½”-1”. HE-7056 - 90° wall plate elbow - pressfit x BSP (F): 15-22mm x ½”-¾”. HE-7057 - tee - pressfit x BSP (F) x pressfit: 15-54mm x ½” & 22-28 x ¾”. HE-7058 - straight connector (with central captive nut and washer) - pressfit x BSP (M): 15-28mm x ½”-1”. HE-7059 - straight connector - pressfit x captive nut and washer: 15-28mm x ¾”-1¼”. V-type connection: HE-7150 - straight connector - pressfit x BSP (M): 15-54mm x ½”-2”. HE-7151 - straight connector - pressfit x BSP (F): 15-54mm x ½”-2”. HE-7152 - straight connector (with central captive nut and washer) - pressfit x BSP (F): 15-28mm x ½”-1”. HE-7153 - straight connector (with central captive nut and washer) - pressfit x pressfit: 15x15-28x28mm. HE-7154 - 90° elbow - pressfit x BSP (M): 15-28mm x ½”-1”. HE-7155 - 90° elbow - pressfit x BSP (F): 15-28mm x ½”-1”. HE-7156 - 90° wall plate elbow - pressfit x BSP (F): 15-22mm x ½”-¾”. HE-7157 - tee - pressfit x BSP (F) x pressfit: 15-54mm x ½” & 22-28 x ¾”. HE-7158 - straight connector (with central captive nut and washer) - pressfit x BSP (M): 15-28mm x ½”-1”. HE-7159 - straight connector - pressfit x captive nut and washer: 15-28mm x ¾”-1¼”.

Approval Holder:

YUHUAN HONGEN VALVE CO., LTD

Company Name

YUHUAN HONGEN VALVE CO., LTD

Address

Sanliancun, 317605, Yuhuan, Zhejiang, China

View All Listings by this Company

Manufacturer:

YUHUAN HONGEN VALVE CO., LTD

Company Name

YUHUAN HONGEN VALVE CO., LTD

Address

Sanliancun, 317605, Yuhuan, Zhejiang, China

View All Listings by this Company

VSH XPRESS Range of copper press fittings with EPDM rubber ‘O’-rings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2106049

Size:

12mm - 108mm.

Marking:

DVGW, XPRESS & SIZE ON BODY

Installation Requirements:

R001

Expiry date:

30/06/2026

Model:

7001 22, 7002 22, 7001 15, 7002 15, 7040 22, 7130 15 & 7130 22 PRESS FITTINGS 6270 Copper Press Coupling: 12 - 108mm. 6271 Copper Press Coupling: 12 - 54mm. 6240 Reducer press x press: 15mmx12mm - 54mmx42mm. 6243 Reducer x press: 15mmx12mm - 108mm x 88.9mm. 6001 Bend 90° x press: 12-108mm. 6002 Bend 90° press x press: 12 - 108mm. 6130 Equal Tee 3 x press: 12 - 108mm. 6040 Bend 45° x press: 12 - 108mm. 6041 Bend 45° press x press: 12 - 108mm. 6301 Endcap press: 12 - 108mm. 6131 Reducing Tee 3 x press: 15mmx15mmx12mm - 108mm x 76.1mm x 108mm. 6085 Full Crossover: 15mm x 15mm - 22mm x 22mm. 6086 Partial Crossover: 15mm x 15mm - 22mm x 22mm. 6510 Flange PN16: 76.1mm.

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company