'ABS GAR-220 SA'. Natural (appears yellow coloured), injection moulded ABS material. For use with water up to 85°C.
'Super Poxy 505TL'. Factory applied, grey coloured, two-component Epoxy coating. Mix Parts A & B in a 100:20 weight ratio and apply as per manufacturer's TDS dated '2026.01.14'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Nitomortar TC2000'. Factory applied, two-component, grey coloured (once mixed and applied) epoxy resin sealing compound. The material is supplied in pre-weighed quantities (60% base, 40% hardener), to be applied in accordance with manufacturer's instructions 'FO SA/NITOMORTAR TC2000/0110/19'. Cure for 7 days@25°C and 55% humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DUAYEN ANTIBLAST GEÇIRIMSIZ SPREY BOYA KAPLAMA'. Factory applied, two-component, black coloured (once mixed and applied), Polyurea coating. Mix parts A & B in a 1:1 volume ratio and apply as per manufacturer's TDS 'Rev01', date of issue '22.04.2024'. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP TANK 500 PW'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a 3:1 volume ration and apply two coats as per manufacturer's TDS '0724'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JA-Blue'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate to 40°C and then spray apply as per manufacturer's instructions issued ‘March 2017, V4.1’. Cure for 20 minutes@180°C. For use with water up to 85°C.
‘SIGMAPRIME 700 HSV’ (yellow/green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured in PPG SSC Co., Ltd. in Ulsan, South Korea). Mix parts A & B of ‘SIGMAPRIME 700 HSV’ (yellow/green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. P757’, dated ‘February 20 2025 (Revision of February 10 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200’ (yellow/Green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured by PPG SSC Co., Ltd. in Ulsan, South Korea). Mix parts A & B of ‘SIGMAPRIME 200’ (yellow/Green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7416’, dated ‘June 06 2025 (Revision of May 01 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 700 HSV’ (yellow/Green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured by PPG Coatings (Kunshan) Co., Ltd. in Kunshan, China). Mix parts A & B of ‘SIGMAPRIME 700 HSV’ (yellow/Green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. P757’, dated ‘February 20 2025 (Revision of February 10 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200’ (yellow/Green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured by PPG Coatings (Kunshan) Co., Ltd. in Kunshan, China). Mix parts A & B of ‘SIGMAPRIME 200’ (yellow/Green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7416’, dated ‘June 06 2025 (Revision of May 01 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE® EA 3478™'. Factory applied, dark grey coloured, two-component epoxy coating. Mix parts A & B in a 7.25:1 weight ratio and apply as per manufacturer's Technical Data Sheet dated 'November 2016'. Cure for 24 hours@22°C. For use with water up to 23°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Intergard 269’ primer for use with ‘Interline 975’ coating. Site applied, off-white coloured (once mixed and applied) epoxy coating system comprising of a two-part primer and two-part topcoat. Mix parts A & B of ‘Intergard 269’ primer in a 4:1 volume ratio and apply as per manufacturer’s TDS reference ‘206’, dated ‘11/03/2016’. Cure for 24 hours@10°C. Mix parts A & B of ‘Interline 975’ coating in a 2.2:1 volume ratio and apply as per manufacturer’s TDS reference ‘4236’, dated ‘04/02/2015’. Cure for 14 days@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Safecure Super’. White coloured, spray applied SBR latex solution intended to act as a concrete curing membrane. Apply as per manufacturer`s 'Tech Data Sheet no. 306', 'Revision no. v4', dated '02.01.2026'. Cure for 14 days at 25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Unitec 500 Pro'. Off-white coloured NBR/fibre gasket material manufactured by calendaring. For use with water up to 85°C.
‘DR-PNL-WT’. Ivory coloured, compression moulded (also known as hot pressed), GRP panel. For use with water up to 60°C.
‘PIPECO KOREA 2025 Premium Tank Panel’. Grey (beige) coloured, compression moulded GRP panel. For use with water up to 55°C.
'VE 90606'. Orange coloured (transparent), injection moulded vinyl ester resin material. For use with water up to 50°C.
'PT-100' Grease. White coloured (opaque), non-miscible grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'F15222 Center & PHCB042 Center'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
‘Silicone Grease A665016, 665016-TUB, A665017, ASG50, AHPSG50, PH041, PHCB041/F15220 & PHCB042/F15222’. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Durethan BKV30F 901510 SR1'. Black coloured, injection moulded nylon material. For use with water up to 65°C.
'Grilamid TR ICR 12 LS natural' (appears white, transparent), 'Grilamid TR ICR 12 LS yellow 6908' (yellow coloured) and 'Grilamid TR ICR 12 LS blue 4271' (blue coloured). Injection moulded PA MACM12/X materials. For use with water up to 85°C.
'Parixit HDPE Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 60°C.
'Parixit HDPE Fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 60°C.
'Neproplast HDPE Fittings'. Black coloured, injection moulded HDPE (PE100) fittings. For use with water up to 60°C.
'FIRAT HDPE 100 fittings'. Black coloured, injection moulded HDPE electrofusion fittings. For use with water up to 23°C.
'FIRAT HDPE 100 Pipe'. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 23°C.
'Polyatlas PE100 Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 23°C.
'SAF SUDAIR PE-100 Pipes'. Black coloured (blue external stripe), extruded PE-100 pipes. For use with water up to 85°C.
'A001 Series PEX-AL-PEX Pipe'. Extruded pipe with a white coloured inner layer, aluminium middle layer and white coloured outer layer. For use with water up to 75°C.
'Hepworth PE 80 & PE 100 Pipes'. The extruded PE 80 pipes are black coloured. The extruded PE 100 pipes are either black or blue coloured. For use with water up to 60°C.
‘Art. 040 Full Face Flange’. Black coloured, hot injection moulded HDPE flange fitting. For use with water up to 23°C.
'MD1001 PPR Pipe'. Green coloured, extruded PPR pipe. For use with water up to 65°C.
'Repair Stick Steel' & 'Repair Stick Stainless Steel'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per manufacturer’s TDS dated 17.09.2025. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemiline AE 004 FB 26'. Black coloured, butyl material manufactured by calendaring. Shore hardness 65A. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EP-G70B' Gaskets and 'O' rings. Black coloured, compression moulded, EPDM gaskets and 'O' rings. Shore hardness 70. Tested in-radius size 1.6mm. For use with water up to 23°C.
'EPDM-825-cmk (H80)/mld'. Black coloured, compression moulded EPDM material. Shore hardness 80 ShA. Tested in-radius size 1.13mm. For use with water up to 23°C.
'YL-EA-70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.11mm. For use with water up to 65°C.
'Chemiline AG 030 FB 62'. Black coloured, EPDM material manufactured by calendaring. Shore hardness 60A. Tested in-radius size 1.0mm. For use with water up to 65°C.
'603.0703.046 - EPDM PX Black SH 78'. Black coloured, injection moulded EPDM material. Shore hardness 78. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM-LJHY'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP70B002'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'01/B80NBR 'O' rings' and gaskets. Black coloured, injection moulded NBR 'O' rings and gaskets. Shore hardness 80. Tested in-radii sizes between 0.5mm & 2.0mm. For use with water up to 23°C.
'LSR2650, LSR2660 & LSR2670'. Black coloured, injection moulded liquid silicone rubber materials. Shore hardness between 50 & 70. 'LSR 2660 White'. White coloured, injection moulded liquid silicone rubber material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 65°C.
'KEG-2003H-30, KEG-2003H-40, KEG-2003H-50, KEG-2003H-60 & KEG-2003H-70 (no postcure)'. Translucent, compression moulded, silicone rubber materials. Shore hardness between 30 & 70. Tested in-radii sizes between 0.18mm & 5.9mm. For use with water up to 85°C.
'PSX 34 Epoxy adhesive'. Site applied, two-part Epoxy adhesive/sealant comprising of a black coloured paste and grey coloured paste, supplied as a pre-weighed kit. Mix, apply and cure as per manufacturer’s TDS ‘ADH4710ENG_PotableWater Feb 2026’. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PSX 60 Epoxy adhesive'. Site applied, two-part Epoxy adhesive/sealant comprising of a black coloured paste and grey-white coloured paste, supplied as a pre-weighed kit. Mix, apply and cure (refer to Minimum Joint Cure Time) as per manufacturer’s TDS ‘ADH4720ENG_PotableWater Feb 2026’. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 747 PVC Cement'. Blue coloured solvent cement. Apply as per manufacturer's PDS '747-05-2025'. Cure for 4 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 795 Clear PVC Cement'. Clear solvent cement. Apply as per manufacturer's PDS '795-05-2025'. Cure for 4 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Single hole, single outlet (fixed) electronically controlled tap assembly (chromium plated brass body), flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator, and the inlet hoses are supplied with stainless steel strainers. The inlet hose has and an approved check valve cartridge: however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Page 227 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
