'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Neropoxy Solvent Free Coating White & Red'. Factory applied, white or red coloured, two-component epoxy coating comprising of a base and hardener. Mix base and hardener in a 3:1 mass ratio. Cure for 10 days@28°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA 801 Blue 502'. Factory applied, grey coloured modified PE blend coating. Pre-heat part/item to be coated to 340°C, dip into a fluidized bed containing the coating and then allow to cool at room temperature. No cure required For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nu Vista'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours at 45°C and then 28 days (672 hours)@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Infra Pro'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours@45°C and then 28 days (672 hours) @35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPX-213H Grey'. Factory applied, grey coloured, epoxy powder coating. Apply and cure as per manufacturer's instructions 'XL-R-019-R2' dated '2015-11-12'. For use with water up to 85°C.
'SC2 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-002 issue 1' dated 09-08-2016. For use with water up to 85°C.
'Protecfull SFP 108'. Factory applied, two-component, cream coloured polyurethane coating. Mix part A & part B in a 75:25 volume ratio and apply as per manufacturer's instructions reference '016. Ed.01.21' dated August 24, 2021. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP-I-103'. Factory applied, blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturer's instructions issue 'EPOXY86315', dated 'Nov. 15th, 2020'. For use with water up to 65°C.
'Rilsan (MagnaCoat 5501 F)'. Factory applied, white coloured (opaque), polyamide powder coating. Apply as per manufacturer's instructions dated 02/01/2018. Cure for 10 minutes@230°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FIBER TECH 80, Low VOC fiberglass resin'. Factory applied, brown coloured polyester resin & fibreglass. Apply as per manufacturer's method statement reference 'PP-GRP-092021-R1' dated '21 Sept. 2020'. Cure for 48 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC1 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-001 issue 1' dated 09-08-2016. For use with water up to 85°C.
'PMSP5072-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5104-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
"Bond-It Tanking Slurry". Site applied, grey coloured, two part (powder & water) cementitious waterproof coating. Mix and apply as per manufacturer`s instructions 'Version 9' dated 06/08/20. Cure for 12 days at 7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AFM 34/2'. Green/grey coloured fibre gasket material manufactured by calandering. For use with water up to 85°C.
'568H+L101'. Natural (appears off-white in colour), injection moulded GRP material. For use with water up to 70°C.
`8601-A`. Extruded, dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. Shore hardness 85. For use with water up to 85°C.
'Addisil WTG 1'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Plustek PA303G6BK16'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'TYPLEX-1055'. Grey coloured, extruded Polybutylene-1 material. For use with water up to 85°C.
'XC2'. Black coloured, PEEK washer manufactured by filament winding. For use with water up to 85°C.
'Xytrex 116'. Dark grey coloured, hot compression moulded PEEK washer. For use with water up to 85°C.
‘EURO electrofusion fitting'. Black coloured, injection moulded HDPE electrofusion fitting. For use with water up to 85°C.
'Shield MDPE Fitting'. Black coloured, injection moulded PE80 fitting. For use with water up to 85°C.
'Shield MDPE Pipe'. Black coloured, extruded PE80 pipe. For use with water up to 85°C.
`Comisa' pipe. Triple layered, extruded pipe consisting of a translucent PE-RT inner layer, aluminum middle layer and white coloured PE-LMD outer layer. For use with water up to 85°C.
'+GF+ HAKAN PE-RT White Pipe'. White coloured (opaque), extruded PE-RT pipe. For use with water up to 85°C.
'+GF+ HAKAN PE-XB White Crosslinked Pipe'. White coloured (opaque), extruded PE-XB pipe. For use with water up to 85°C.
'+GF+ HAKAN PE-RT EVOH Pipe'. Extruded pipe with a white coloured (opaque) PE-RT inner layer and an orange coloured EVOH outer layer. For use with water up to 85°C.
'Revolve N-525 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Klimapress Fitting'. Black coloured, injection moulded PPSU fitting. For use with water up to 85°C.
'ROMAKLIMA Pipe'. Extruded, triple layered pipe comprising of a green coloured PP-R inner layer, green coloured PP-R (with glass fibre) middle layer and green coloured PP-R outer layer (with dark green stripes). For use with water up to 85°C.
'Romafaser CT pipe'. Extruded, triple layered pipe comprising of a green coloured PP-RCT inner layer, green coloured PP-RCT (with glass fibre) middle layer and green coloured PP-RCT outer layer. For use with water up to 85°C.
`PPR 001` Pipes. White (with red external stripe) or tangerine coloured, extruded polypropylene pipes. For use with water up to 85°C.
'Q-Therm'. Extruded, multi-layered PP-R CT pipe comprising of a green coloured PPR inner layer, translucent PPR/glass fibre middle layer and green coloured PPR outer later. For use with water up to 85°C.
'+GF+ Aquasystem PP-RCT'. Extruded, green coloured (with yellow external stripe), multi-layered pipe. All three layers of the pipe are green coloured and made from PP-RCT but the middle layer also has glass fibres. For use with water up to 85°C.
'F420B00 natural (appears off-white), F420B99 (black coloured) & F410K01 (white coloured)'. Injection moulded, glass filled polypropylene materials. For use with water up to 85°C.
'Xytrex 115'. Black coloured, hot compression moulded PTFE washer. For use with water up to 85°C.
'Xytrex 120'. Black coloured, hot compression moulded PTFE washer. For use with water up to 85°C.
`FORWA PTFE tape`. White coloured, extruded PTFE tape. For use with water up to 85°C.
'Hepworth CPVC Pipe'. Grey coloured, extruded CPVC pipe. For use with water up to 85°C.
'Art. 0985077205 Anti-leak Tape'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet version '001' dated 26.07.2021. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4800'. Site applied, grey coloured cementitious repair mortar. Mix Intercrete 4800 and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP7008S 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 60°C.
'EP1/1/6 BLK' O-rings. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 1.75mm. For use with water up to 85°C.
'EP906'. Black coloured, extruded EPDM washer. Shore hardness 90. Tested in-radius size 1.4mm. For use with water up to 85°C.
'ERIKS 55985 Gaskets & ‘O’ rings'. Black coloured, compression moulded EPDM gaskets & ‘O’ rings'. Shore hardness 70A. The gaskets have a tested in-radius size of 1.0mm. The ‘O’ rings have a tested in-radius size of 1.76mm. For use with water up to 85°C.
Page 22 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
