'POLIMID A SG NATURALE WR'. Natural (appears white in colour), injection moulded PA 66 material. In February 2025 'POLIMID A SG BLACK WR-PA66', black coloured, injection moulded PA 66 material was added to the approval. For use with water up to 85°C.
'Power Plastic HDPE Pipe'. Black coloured, extruded HDPE pipe (manufactured from SABIC P6006). For use with water up to 85°C.
'AGRULINE PE100RC Pipe'. Black coloured, extruded polyethylene pipe. For use with water up to 85°C.
'Jain MDPE (PE 80) Pipe'. Blue coloured, extruded PE80 pipe. For use with water up to 65°C.
'EGPI MDPE BL-W Pipe'. Black coloured (with blue stripes), extruded MDPE pipe. For use with water up to 85°C.
‘LURANYL® KR 2402 TW 35061, LURANYL® KR 2403 G4 TW 26343 & LURANYL® KR 2403 G6 TW 26343’. Black coloured, injection moulded polyphenyleneoxide/polystyrene materials. In May 2025, ‘LURANYL® KR 2403 G2 TW GY4090-24’ & ‘LURANYL® KR 2403 G6 TW GY4040-24’, dark grey coloured, injection moulded polyphenyleneoxide/polystyrene materials were added to the approval. All grades are for use with water up to 85°C.
'AH40-7484Z'. White coloured, injection moulded PPE material. For use with water up to 65°C.
'POWERtherm PP-R Fittings'. Green coloured, injection moulded PP-R fittings (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'Irriplast PP Fitting'. Black coloured, injection moulded PP fitting. For use with water up to 85°C.
'RAKplus'. Green coloured, extruded PP-R pipes. For use with water up to 85°C.
'Wavin PP-R Fitting'. Grey/green coloured, injection moulded PP-R fitting. For use with water up to 85°C.
'Wavin PP-R Solid Wall Pipe'. Grey/green coloured (with external red stripe), extruded PP-R pipe. For use with water up to 85°C.
'Borstar® RA150E'. Natural (appears off-white) polypropylene material for injection moulding and extrusion purposes. For use with water up to 85°C.
'Topilene R202P'. White coloured, extruded polypropylene material. For use with water up to 85°C.
'PTFE2215 seal'. White coloured (opaque), compression moulded PTFE seal. For use with water up to 85°C.
'Bush (25122200)'. Dark grey coloured, extruded NEP-25%carbon/PTFE component. For use with water up to 85°C.
'+GF+ PVC-C Pipe'. Grey coloured, extruded PVC-C pipe. For use with water up to 85°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 04/06/218. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CH200'. Brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'version 24/05/2018'. Cure for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
Page 209 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
