Range of screw down angle valves with brass bodies (chromium plated) and NBR ‘O’-rings with a dome type operating member. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperatures: model 510052 = 95°C and model 510060 = 85°C.
Carbongraphite AG21 P/T, MCI320/T & AG21P-3M/T. Dark grey coloured, phenolic resin filled, carbon graphite rings manufactured by cold pressing. For use with water up to 85°C.
'AMMT-001G Two Component Epoxy Resin Coating/Ceramic Epoxy Coating'. Factory applied, off-white coloured, two-component epoxy coating. Components A and B are preheated to 60°C, mixed in a volume ratio of 1:1.& applied as per manufacturer's instructions 'version 2.00', dated '11/01/2021'. Cure for 1 hour@60°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'issue reference SPI 20170215' dated 21st January 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT (grey)'. Factory applied, grey coloured, epoxy powder coating. Apply as per manufacturer's TDS dated January 21st 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JPC Liquid Epoxy Paint'. Factory applied, red coloured, two-component epoxy paint. Mix components A & B in a 3:1 volume ratio and apply as per manufacturer's instructions ' JPC-FG-A/06-21/009 & JPC-FG-B/06-21/009' dated '02/06/2021'. Cure for 7 days@34°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KARUMEL EX4412 (RAL5005) & KARUMEL EX4412 (Blue)'. Factory applied, blue coloured epoxy powder coatings. Apply as per manufacturer's application guide for potable water reference number 'KCSA-21090101' dated September 2021. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LNXFSY'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X202101207F' dated '2021-12-07'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MS 1555'. Factory applied, dark blue/grey coloured vitreous enamel coating. Apply as per manufacturer's instructions 'I.PBE.06.04' dated November 22, 2021 and 'TPE.09.056.02' dated August 19, 2014. Cure for 14 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 193 of 320
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
