'HT 204'. Grey coloured carbon bearing, pressed, sintered, impregnated with phenolic resin and rebaked. For use with water up to 85°C.
NY Blue PP. Blue coloured, factory applied nylon powder coating. Apply as per manufacturer's instructions for 'NY Blue PP nylon powder' dated 01-05-25, then post cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue and Jotapipe AC - 1003 Green'. Factory applied, blue or green coloured fusion bonded epoxy coatings (manufactured in Dubai, U.A.E). Apply as per manufacturer's Technical Data Sheet dated 26th September 2019. Cure for 2 minutes@245°C. The blue coating is for use with water up to 85°C. The green coating is for use with water up to 23°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-XP2501'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'XP2503-010', dated '2025-03-25'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-RVK2025'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'RVK2503/25', dated 'March 25, 2025'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Guom-07'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a weight ratio of 1:1.5:0.6 and apply as per manufacturer's User Instructions 'GUOM-24', 'Vision: B', dated '2024-11-5'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SWEP Sealix Coating'. Factory applied, colourless (translucent) silicon dioxide coating. Apply as per manufacturing instructions ref. 'Sealix-2020-01' dated 2020-01-01. Cure for 3 hours@300°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MAVM554'. Factory applied, blue coloured, epoxy powder coating. Apply as per manufacturer's data sheet 'FR.07.03.18', dated 09.19. Cure for 10 minutes at 160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Solvent Free Epoxy Coating XH4205'. Factory applied, white coloured, two-component epoxy coating. Mix Coat 1 (XH4205/grey coating & XH7322) in a 5:1 weight ratio and apply as per ‘Application Procedure 2024IV, v1', issue date '2025/01/01'. Cure for 24 hours@25°C. Mix Coat 2 (XH4205/white coating & XH7322) in a 5:1 weight ratio and apply as per ‘Application Procedure 2024IV, v1', issue date '2025/01/01'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue & Green. Factory applied, green or blue coloured epoxy coatings (manufactured in Dammam, Saudi Arabia). Apply as per manufacturer's MTI '001 - 2024 - SA – EN'. Cure for 4 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electroline ES 424'. Factory applied, white coloured, two-component epoxy coating. Mix Part A and Part B in a volume ratio of 2:1 and apply as per manufacturer's TDS 'ECL/ TDS / ES424', version '0', dated '05.01.2024'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat Epoxy Blue Patch Up Paint (PFC/1017)'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:2 volume ratio and apply as per manufacturer's IFU 'DOC/PFC/PU/101', dated '01.04.2024'. Cure for 8 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`MECH WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions '24136' dated 2025/1/26. For use with water up to 85°C.
'EM6/35/7541/1'. Factory applied, dark blue coloured Porcelain (vitreous) enamel coating. Apply as per manufacturer's instructions 'IS_003', 'rev. 01'. Cure for 16 min 875°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ET-52184 & ET-52185'. Factory applied, black coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure both undercoat and finishing coat for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELM EPX 13'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions to end users reference no. 'ELM/2019/10/001' dated '23/08/2024'. Cure for 10 minutes@130°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyflon PTFE TC-7808-19 Grey PTFE Coating'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's technical data sheet dated 'June 8, 2012'. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Carboguard AQP FC Part A and Part B'. Site applied, grey coloured (once applied) epoxy coating. Mix Parts A & B in a weight ratio of 1:1 and apply as per manufacturer's Product Data Sheet '8163', dated 'March 2025'. Cure Coat 1 for 24 hours at 20°C and Coat 2 for 7 days at 20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monoflex W'. Grey coloured, extruded TPO 'tape'. Shore hardness 91. Tested in-radius size between 0.45mm & 1.0mm. For use with water up to 70°C.
'LEAKBLOK® P100'. Green coloured fibre/NBR gasket material manufactured by calandering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'EPDM W8528'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SL7065/SL7015'. Extruded, triple layered hose comprising of a translucent, silicone inner layer, white coloured polyester middle layer and translucent, silicone outer layer. Shore hardness 70. Tested in-radius size of complete hose is 1.8mm. For use with water up to 65°C.
'LH-02 EPDM Hose'. Black coloured, extruded EPDM rubber hose. Shore hardness 80. tested in-radius size 0.8mm. For use with water up to 85°C.
'7740 WPG'. White coloured, silicone based lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'A7G10E'. Black coloured, injection moulded PPA material. For use with water up to 85°C.
'Grilon AG-30 FWA Black'. Black coloured, injection moulded, PA66-GF30 material. For use with water up to 85°C.
'RPL-104'. Off-white coloured, unsaturated polyester resin material, manufactured by hand lay up process. Between March 2025 and March 2026, the material was for use with water up to 23°C. Between April 2026 and March 2030, the material is for use with water up to 50°C.
'T-MECH PE-Xb Pipe’. White coloured (opaque), extruded PEX pipe. For use with water up to 85°C.
'PE002'. Blue coloured, HDPE fitting manufactured by mould pressing. For use with water up to 60°C.
'PIPELIFE - ARILI HDPE PE100 Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 23°C.
‘SABIC P6006AD’. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
'Tecotek OP20 GR30 BG018 01 0A QF'. Beige coloured, injection moulded PPO/HIPS material. For use with water up to 85°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
'Dalcon 001'. White coloured, compression moulded or extruded PTFE material. For use with water up to 85°C.
'PVDF Solef® 1008/0HP1'. White coloured, injection moulded PVDF material. For use with water up to 85°C.
'PVDF Solef® 1010/0HP1'. White coloured, injection moulded PVDF material. For use with water up to 85°C.
'PVDF Solef® 1010/0UP1'. White coloured, injection moulded PVDF material. For use with water up to 85°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'51M7568'. Black coloured, injection moulded EPDM material. Shore hardness 75 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AA7BCZ'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'NBR 70 M066'. Black coloured, injection moulded NBR 'O' ring. Shore hardness 70. Tested in-radius size 3.0mm. For use with water up to 23°C.
'NE7130-XT'. White coloured (translucent), injection moulded Silicone rubber. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
'LOCTITE® 577™ & LOCTITE® SF 7649 Activator'. Yellow coloured thread sealant for use with light green coloured activator. Apply LOCTITE® 577™ as per manufacturer's technical data sheet reference ‘0.0’, dated November 2024 and LOCTITE® SF 7649 Activator as per manufacturer's technical data sheet reference ‘1.4’, dated June 2014. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Cyberbond® SH27'. Yellow coloured (translucent) anaerobic adhesive. Apply as per manufacturer's TDS 'V01.005.en-gb.001'. For use with water up to 23°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'WS27TF Pipeseal'. Yellow coloured anaerobic adhesive. Apply as per manufacturer's datasheet issue '1.0'. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Vyncolit BXE650W'. Black coloured, injection moulded phenolic material. For use with water up to 85°C.
'JFD-PVCR01'. Beige coloured, extruded PVC pipe liner. For use with water up to 23°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). The flow is controlled via a solenoid valve, activated via an infra-red sensor and temperature controlled via manual lever. The inlets incorporate single check valves cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Page 181 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
