'P0667 Lid Support'. Light green coloured (opaque), GRP lid support component manufactured by pulltrusion. For use with water up to 23°C.
‘BESLUX FLUOR FLUID 06’. Transparent, colourless PFPE lubricating fluid. Apply as per manufacturer’s instructions. For use with water up to 85°C.
'Simona PE100 black fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'Supreme PE Pipe TSIL G'. Black coloured (with blue stripes), extruded PE 100 pipe. For use with water up to 60°C.
'BUPLEN 6231'. Colourless, injection moulded polypropylene material. For use with water up to 23°C.
'Ganga 50, 60, 70, 80 & 90'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 90 ShA. Tested in-radius size 1.1mm. For use with water up to 85°C.
'EPDM50BKWS, EPDM55BKWS, EPDM60BKWS, EPDM65BKWS, EPDM70BKWS, EPDM75BKWS & EPDM80BKWS'. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'WRWNR75D'. Black coloured, natural rubber material manufactured by calendaring. Shore hardness 75 Shore D. Tested in-radius size 0.6mm. For use with water up to 23°C.
'TamAcryl 2000 Orange or Blue with corrosion inhibitor', orange coloured or blue coloured (once mixed), site applied acrylic grouts. Mix Part A (orange or blue) with 2% accelerator and then mix with Part B (colourless) in a 1:1 volume ratio. Apply as per manufacturer’s TDS 'V1UK20 – 2020.10.22'. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Bidet seat assembly which discharges via a push button actuated solenoid valve and utilises a ‘Type AB’ air gap arrangement (verified by test - suitable for backflow prevention against Fluid Category 5). Maximum working pressure 8 bar. Maximum operating temperature 40°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (various finishes - see model). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The TK-201LT66 and TK-201LT95 models have a multi-layer PEX lined hose between the solenoid and the spout. The TK-201LT65 models have a stainless steel braided PEX lined flexible hose between the solenoid and the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (various finishes - see model). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The IRBS5-CP models have a multi-layer PEX lined hose between the solenoid and the spout. The TK-201LT65 models have a stainless steel braided PEX lined flexible hose between the solenoid and the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Side entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of aerator kits incorporating plastic flow regulators (1.9l/min, 3.5l/min & 5.0l/min) with plastic bodies and EPDM ‘O’ rings. Plastic adaptors, NBR washers and chromium plated brass housings may also be supplied as part of the kit. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a waterfall type). The products are supplied with a click type waste. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of single-hole, single outlet, fixed combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with level operating members. The spout outlets incorporate plastic aerators. The products are supplied with click wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 181 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
