'UW TPE HEA-ISO (manufactured from NAKAN HEA 407 EX)'. White coloured (translucent), extruded TPE hose. Shore hardness 66. Tested in-radius size 0.39mm. For use with water up to 65°C.
'Draka Comteq Cable Sheath: R607581 and R698927. Black coloured, extruded polyethylene cable sheath. For use with water up to 85°C.
'Egelen PE100 & Egeplast 9010 pipes'. Egelen PE100 is a single layered, black coloured, extruded PE100 pipe. Egeplast 9010 is a dual layered, extruded PE100 pipe consisting of a black coloured inner layer and a blue coloured outer layer. For use with water up to 23°C.
'N-PU.95R'. Red coloured, injection moulded PUR material. For use with water up to 23°C.
'MasterCrete ANC 932'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1' dated '09.12.2024'. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MasterCrete ANC 920'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1', dated '09.12.2024' Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterCrete ANC 915’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 1', dated '09.12.2024'. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'798F'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EPDM50P - ELAST45901, EPDM60P - ELAST46901, EPDM70P - ELAST47901 & EPDM80P - ELAST48901’. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.3mm. For use with water up to 85°C.
'WAGUNIT H 1005'. Light brown coloured, compression moulded natural hard rubber. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve that is activated via an infrared sensor. Certain models incorporate a mixer spout which incorporates a manual temperature control. The spout outlets also incorporate a plastic flow straighter. Maximum working pressure; 5 Bar Maximum operating temperature: 60°C
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of spring loaded, resilient trim check valve cartridges with plastic body. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Spring loaded, resilient trim, in-line check valve cartridge with NBR & EPDM ‘O’-rings, plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 8.6 Bar. Maximum operating temperature 60°C.
Undercounter boiling water cistern with a stainless steel body, stainless steel element and silicone ‘O’-rings and gaskets. Maximum working pressure 8.0 bar. Maximum operating temperature 95°C.
Range of stainless steel calorifiers. Max working pressure 10 bar. Max operating temperature 90°C.
Range of flow regulators, aerators and flow straighteners with plastic bodies. Maximum operating temperature 60°C.
Range of balancing valves with DZR brass bodies Maximum operating pressure 25 bar. Maximum operating temperature 99°C
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of balancing valves with DZR brass bodies Maximum operating pressure 25 bar. Maximum operating temperature 99°C
Page 172 of 215
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
