Water Regulations Approval Scheme Ltd

Directory Search Results

WRAS Approval Number: #260115010

Range of blue epoxy coated carbon steel flanged dismantling joints with EPDM sealing rings. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.

Section:: 1220 Fittings for use with Tube and Pipe
Section Subtitle:: Flanged, un-flanged and repair clamps. (external clamps only) Unless specified in the individual approval, the products within this section are not suitable for below ground use WRAS takes no responsibility for the claims made by the manufacturer regarding the effectiveness of the product for providing a repair to fittings to prevent a waste of water.
WRAS Approval Number:: 260115010
Basis of Compliance:: Tested to regulators Specification Test Code Sheets
Size:: DN65-DN1600 flanged.
Marking:: KSB logo, KSB, model, DN, PN and material on data plate on body
Installation Requirements:: R001
Expiry date:: 31/01/2031
Model:: ECOLINE DJ DISMANTLING JOINTS

Approval Holder:: KSB Valves (Changzhou) Co., Ltd.

Company Name
KSB Valves (Changzhou) Co., Ltd.
Address
No.68 Huanbao Four Road, Xinbei District, Changzhou, Jiangsu Province
Country
China

View All Listings by this Company
Manufacturer:: KSB Valves (Changzhou) Co., Ltd.

Company Name
KSB Valves (Changzhou) Co., Ltd.
Address
No.68 Huanbao Four Road, Xinbei District, Changzhou, Jiangsu Province
Country
China

View All Listings by this Company

WRAS Approval Number: #260102013

Type ‘J’ range of plate heat exchangers with stainless steel (AISI 304L or AISI 316L) fin and end plates. Maximum working pressure 3.0 bar (primary circuit) and 10.0 bar (secondary circuit). Maximum operating temperature 80°C.

Section:: 1350 Heat Exchangers
Basis of Compliance:: Tested to regulators Specification Test Code Sheets
Size:: ¾” BSP (M) Primary circuit. ½” BSP (M) Sanitary circuit.
Marking:: Condevo S.p.A. and model on adhesive label on body
Installation Requirements:: R001
Expiry date:: 31/01/2031
Model:: Type ‘J’ range comprising of: PP10FJX. PP12FJX. PP14FJX. PP16FJX. PP18FJX. PP20FJX. PP22FJX. PP24FJX. PP26FJX. PP28FJX. PP30FJX. PP32FJX. PP34FJX. X denotes the body material and is replaced with: 4 = AISI304L 6 = AISI316L

Approval Holder:: Condevo SpA

Company Name
Condevo SpA
Address
Via Luna, Z.A. 26866 Marudo (LO) Italy

View All Listings by this Company

WRAS Approval Number: #260104013

Range of copper brazed, stainless steel (316) heat exchangers in various sizes (4-300 plates, see models). Maximum working pressure: see models. Maximum operating temperature: 99°C.

Section:: 1350 Heat Exchangers
Basis of Compliance:: Tested to regulators Specification Test Code Sheets
Size:: ½” - 3” BSP (M).
Marking:: SWEP, models, PN and tech info on adhesive label on body
Installation Requirements:: R001
Expiry date:: 31/01/2031
Model:: X8T-SC-S - Number or Plates: MIN 4 – MAX 60, Max Flow rate – 4 m3/h - ½”, ¾” - 32/26bar. 10T-SC-M - Number or Plates: MIN 4 – MAX 140, Max Flow rate – 9 m3/h - 3/8” to 1 ¼” - 41/36bar. 15T-SC-M - Number or Plates: MIN 4 – MAX 60, Max Flow rate – 4 m3/h - ½” to 1” - 45/45bar. 16DW-SC-S - Number or Plates: MIN 4 – MAX 140, Max Flow rate – 11,3 m3/h ½” to 1 ¼” - 16/16bar. 16DW-SC-M - Number or Plates: MIN 4 – MAX 140, Max Flow rate – 11,3 m3/h - ½” to 1 ¼” - 45/45bar. 220-SC-S - Number or Plates: MIN 4 – MAX 300, Max Flow rate – 39 m3/h 1” to 2 ½” -25/25bar. 320HT-SC-S - Number or Plates: MIN 4 – MAX 300, Max Flow rate – 61,7 m3/h - 1 ½” to 2 ½” - 33/29bar. 320LT-SC-S - Number or Plates: MIN 4 – MAX 260, Max Flow rate – 76,2 m3/h - 1 ½” to 3” - 25/25bar.

Approval Holder:: SWEP International AB

Company Name
SWEP International AB
Address
Järvgatan 3B, Box 105, 26122 Landskrona
Country
Sweden

View All Listings by this Company
Manufacturer:: SWEP International AB/SWEP Slovakia s.r.o.

Company Name
SWEP International AB/SWEP Slovakia s.r.o.
Address
Box 105, 26122, Landskrona
Country
Sweden
Phone
+46 418400406

View All Listings by this Company

WRAS Approval Number: #260102725

Range of electronically controlled heat interface units (HIU) with a stainless-steel plate heat exchanger providing space heating and instantaneous hot water. The domestic hot water (secondary) circuit incorporates a pressure relief valve (set at 10.0 bar). The inlets and outlets of all circuits incorporate a T-handled spherical valve. Maximum working pressures: 10.0 bar (Primary circuit), 9.5 Bar (Secondary circuit). Maximum operating temperature 95°C. Cold supply only.

Section:: 1465 Heaters
Section Subtitle:: Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:: 260102725
Basis of Compliance:: Tested to regulators Specification Test Code Sheets
Note:: IRN R511 applies to all spherical valves that can be used for draining the system down.
Size:: 1½” BSP (M).
Marking:: Oventrop Logo on body.
Installation Requirements:: R001 R140 R360 R511
Expiry date:: 31/01/2031
Proviso:: Not supplied with a temporary filling loop. A filling loop must be installed with the appropriate backflow prevention device in accordance with Schedule 2 paragraph 7 of the Water Supply (Water Fittings) Regulations 1999.
Model:: 1681580 - Requmaq X-80, 1681480 - Requmaq X-70.

Approval Holder:: Oventrop GmbH & Co KG

Company Name
Oventrop GmbH & Co KG
Address
Paul-Oventrop-Strasse 1, 59939 Olsberg
Country
Germany

View All Listings by this Company

WRAS Approval Number: #260112011

Range of electromagnetic water meters with stainless steel bodies, dark grey ebonite rubber inner liner and stainless-steel (SUS316L) electrodes. Maximum working pressure 16.0 bar. Maximum operating temperature 40°C.

Section:: 1505 Water Meters
Basis of Compliance:: Tested to regulators Specification Test Code Sheets
Size:: DN25 - DN1000 flanged.
Marking:: Q&T INSTRUMENT CO.,LTD., model number, DN size, electrode material (316L), pressure, serial number “YYMMXXXX”, flow arrow and other technical information on adhesive label on body.
Installation Requirements:: R001
Expiry date:: 31/01/2031
Model:: QTLD-X Where: X is replaced by a number between 25 and 1000 to denote (DN) size, e.g., QTLD-25.

Approval Holder:: Q&T INSTRUMENT CO.，LTD.

Company Name
Q&T INSTRUMENT CO.，LTD.
Address
1 Wangbai Road, Huanglong Industrial Zone, Kaifeng City, Henan Province
Postcode
47500
Country
China
Phone
(0086-371)2666-5538
General Email
xiaoyanzhao@huitiantiefulong.com

View All Listings by this Company
Manufacturer:: Q&T INSTRUMENT CO.，LTD.

Company Name
Q&T INSTRUMENT CO.，LTD.
Address
1 Wangbai Road, Huanglong Industrial Zone, Kaifeng City, Henan Province
Postcode
47500
Country
China
Phone
(0086-371)2666-5538
General Email
xiaoyanzhao@huitiantiefulong.com

View All Listings by this Company