‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux QD Exterior Coating'. Factory applied, blue coloured, two-component epoxy coating comprising of a base and accelerator. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet '679', dated 'Jun 2020'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote® 47-20 Brun Rouge'. Factory applied, red coloured (once mixed and applied), two-component epoxy coating. Mix resin and hardener in an 80:20 mass ratio and apply as per manufacturer's instructions dated '15/06/2021'. Cure for 7 days@20°C. For use with water up to 60°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E0-850-5210-001'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'nr.01, rev.00, issue 01' dated 01/082016. Cure for 30 minutes@210°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AMMT-001G Two Component Epoxy Resin Coating/Ceramic Epoxy Coating'. Factory applied, off-white coloured, two-component epoxy coating. Components A and B are preheated to 60°C, mixed in a volume ratio of 1:1.& applied as per manufacturer's instructions 'version 2.00', dated '11/01/2021'. Cure for 1 hour@60°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Intergard 269 & Interline 975’. Site applied, white coloured Epoxy coating system comprising of a base coat and a topcoat. ‘Intergard 269’ is a two-component base coat which comprises of Part A (red/brown coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 7.46:1 and apply as per manufacturer’s TDS ref. ‘206’, dated 08/02/2021. Cure for 12 days@25°C. ‘Interline 975’ is a two-component topcoat which comprises of Part A (white coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 3.12:1 and apply as per manufacturer’s TDS ref. ‘3577’, dated 31/07/2017. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Ultramid® A3EG10 FC Aqua Black 23285’. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'Badadur PBT9 GF30 Natur S1' (appears cream in colour) and 'Badadur PBT9 GF30 grau 930a' (grey coloured). Natural or grey coloured, injection moulded, glass reinforced PBT materials. For use with water up to 85°C.
‘Ultrason® E 2010 G4 Uncoloured’. Beige coloured, injection moulded polyethersulphone material. For use with water up to 85°C.
'Ultrason® E 2010 natur'. Light yellow coloured, injection moulded PES materials manufactured in Germany and South Korea. For use with water up to 85°C.
Page 160 of 1043
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
