'Crystic LS96PA Clear Gel Coat' for use with 'Crystic 2-446 PA GRP resin'. Contact moulded GRP resin, manufactured by hand lamination, for use with off-white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Brett Martin B9333 & B9444'. Blue coloured lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'Polylite 444-M888'. Amber coloured, unsaturated polyester resin material manufactured by liquid casting. For use with water up to 23°C.
'004DP44 Aiva Composite Saddle'. Blue coloured, injection moulded HDPE fitting. For use with water up to 23°C.
'BorSafe ME3440 (black)'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'Ryton R-4-244NA (beige coloured) & Ryton R-4-244NA ECHO RP and Ryton R-4-244BL & Ryton R-4-244BL ECHO RP (black coloured)'. Injection moulded PPS materials. For use with water up to 85°C.
Range of deck mounted, single hole, single outlet (fixed) electronically operated tap assemblies (Chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The products are supplied with a tee piece for installation prior to the solenoid valve. The inlets of the tee piece incorporate a combined NBR gasket and stainless steel filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are also supplied with stainless steel braided PEX lined flexible (connecting) hose assemblies and angled spherical valves incorporating a stainless steel strainer for installation on each inlet. Temperature is controlled by adjusting the opening of each angled spherical valve. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic flow straightener, and the inlet incorporates a plastic filter. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of boiling water dispensers incorporating plastic (3-7.5 litre models) or stainless steel (10-40 litre models) cisterns with silicone ‘O’-rings and seals. The flow to the internal reservoir is controlled via a float valve. The internal reservoir incorporates an overflow which acts a vent. The inlet incorporates a plastic filter. Water is dispensed using either a lever or push button (PLUS models only) operated self-closing tap. Maximum working pressure 5.0 bar. Maximum operating temperature 98°C. Cold supply only.
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes), incorporating a ceramic cartridge headwork with single leaver operating member. The spout outlet is a pull-out spray type incorporating a plastic aerator. The pull-out hose inlet connector incorporates an approved check valve cartridge, however, , the complete assembly has not been tested to demonstrate it provides backflow prevention Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Page 16 of 73
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
