'PROTECSOB BEC3'. Factory applied, mustard coloured (once mixed), two-component epoxy coating. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's TDS reference '28712'. Cure for 15 hours@70°C. For use with water up to 70°C. From December 2023 the coating is for use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘R-4401, E-44131, E-4413, E-4414, E-4420, E440001, E441001, E440002, E441002, E-5402, E-5403, E-5404, E540001. E541001, E540002, E540003, E541003 & E440007’. Factory applied, grey-blue coloured enamel coatings. Apply as per manufacturer’s instructions ‘issue 02/2016’ dated 05.10.2016. Cure for 6 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Poly Guard-HBSFLE-FG-8248 (red)'. Red coloured, 2 component (base and hardener) epoxy coating. Mix and apply as per manufacturer's 'Product Data Sheet and Application Instructions TRPL' issued 'Oct 2015'. revision '02, Dt: 15th Feb-21'. Cure for 7 days at 25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monolevel 844SP'. Site applied, grey coloured, polymer modified cementitious mortar. Mix mortar with water in a weight ratio of 5:0.6. Apply as per manufacturer's instructions 'Bulletin No. ML844SP/031/010' issued July 2020. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ECOCLEAR White Gray 9098’. Off-white/grey coloured, hot pressed GRP single layered panel. For use with water up to 55°C.
'TapTec™ SR1L Na'. Amber coloured, ion exchange resin. For use with water up to 85°C.
'Everbuild Plumber's P12 Silicone Grease (Barcode: 5055492703842)'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'Sanglier SIlicone Spray (1-1)'. Clear (colourless) silicone spray lubricant. Apply as per manufacturer's TDS 'issue 1' dated 28/01/2022. For use with water up to 85°C.
'Carbonfluortec 9720'. White coloured (opaque) lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'SG300'. Clear (colourless) silicone spray lubricant. Apply as per manufacturer's datasheet 'issue 1' dated January 2022. For use with water up to 85°C.
'Grivory HT1V-5 FWA grey L2172.5'. Grey coloured, injection moulded PA6I/6T-GF50 material. For use with water up to 85°C.
‘ULTRAMID® A218W V30 Natural-C’ (natural, appears off-white) & ‘ULTRAMID® A218W V30 Black-C’ (black coloured). Injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Tecomid NA40 GR30 BK250 HS QW'. 'Tecomid NA40 GR35 BK250 HS QW'. 'Tecomid NA40 GR40 BK250 HS QW'. 'Tecomid NA40 GR45 BK250 HS QW'. 'Tecomid NA40 GR50 BK250 HS QW'. Black coloured, injection moulded, glass fibre reinforced (30% - 50%), PA66 materials. For use with water up to 85°C.
'Tecacomp PEEK 450 natural (1015088)'. Beige coloured, extruded PEEK material. For use with water up to 85°C.
'TONDO TECAPEEK Natural'. Beige coloured, extruded PEEK material. For use with water up to 85°C.
'Flow Reducer Bp V2 ½ 34 9957, Flow reducer Bp V2 ½ short 34 9965 blue & Flow reducer Bp V2 3/8 short 34 9966 blue’. Blue coloured, injection moulded HDPE flow reducers. For use with water up to 23°C.
'Filter 99 3/8 349971 Dark Grey & Filter 99 ½ 349970 Light Grey'. Grey coloured, injection moulded HDPE filters. For use with water up to 23°C.
'Trustlene PE-80 Fittings'. Blue coloured, injection moulded, PE80 electrofusion fittings. For use with water up to 23°C.
'Kingbull PE100 Blue Fitting (391740)'. Blue coloured, injection moulded polyethylene fitting. 'Kingbull PE100 Black Fitting (0103208)'. Black coloured, injection moulded polyethylene fitting. Both for use with water up to 65°C.
'Iglidur® UW160 Bearing'. Grey coloured, injection moulded PE bearing. For use with water up to 85°C.
Page 137 of 394
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
