Screw down stop valve with either gunmetal, stainless steel or brass bodies (see model), EPDM seals and ‘O’-rings and seal washer. 135020 prefix and 0731G0 prefix models have a drain port fitted with an EPDM ‘O’-ring. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.

Section:

2310 Valves

Section Subtitle:

Stop, metal, screw down.

WRAS Approval Number:

240404037

Size:

DN15 – 80 (see models)

Marking:

Kemper logo on body

Installation Requirements:

R001

Expiry date:

30/04/2029

Model:

135010XX00 - Flanged 135020XX00 - Flanged 1702G0XX00 - Male thread 171020XX00 - Female thread 1732G0XX00 - Male thread - (DN15 - 50) 1742G0XX00 – Male thread 190020XX00 – Female thread 191020XX00 – Female thread 0730G0XX00 – Male thread 0731G0XX00 – Male thread Model added November 2024: 1732G0XX00 – DN65 – 80.

Product Images

Approval Holder:

Gebr. Kemper GmbH + Co. KG

Company Name

Gebr. Kemper GmbH + Co. KG

Address

Harkortstr. 5 57462 Olpe Germany

Phone

+49(0) 27618910

General Email

info@kemper-olpe.de

View All Listings by this Company

Range of bedpan washing & disinfection machines. The flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure - See models Maximum operating temperature - 90 °C

Section:

2360 Washing Machines

Section Subtitle:

Bedpan and disinfecting. Washing machines in this section will indicate the category of backflow prevention built into each appliance. The location and the use of the washing machine will determine any additional backflow protection that may be required.

WRAS Approval Number:

240102706

Size:

½” BSP (M)

Marking:

Stanbridge on control panel. Stanbridge, serial number and company information on date plate on front panel.

Installation Requirements:

R001

Expiry date:

31/01/2029

Model:

CS1 ST – 000101 – 4.14 Bar CS2 ST – 000-201 – 4.14 Bar CS3 ST – 000-301 – 4.14 Bar CS3 HD – 000-302 – 8.00 Bar Slimline – 000-401 – 8.00 Bar

Product Images

Approval Holder:

Stanbridge Ltd

Company Name

Stanbridge Ltd

Address

Unit 78, Powder Mill Lane Quester Estate Dartford

Postcode

DA1 1JA

Country

United Kingdom

Phone

+44 (0)1689 806500

General Email

claire@stanbridge.co.uk

View All Listings by this Company

Manufacturer:

Stanbridge Ltd

Company Name

Stanbridge Ltd

Address

Unit 78, Powder Mill Lane Quester Estate Dartford

Postcode

DA1 1JA

Country

United Kingdom

Phone

+44 (0)1689 806500

General Email

claire@stanbridge.co.uk

View All Listings by this Company

Electrolytic scale reducer, with a chromium plated copper body and zinc alloy anodes, for use with copper pipe (manufactured to BS EN1057) Maximum working pressure 10.0 bar. Cold water use only.

Section:

2410 Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic

Size:

15mm compression

Marking:

Cura Trademark of B.E.S on adhesive label on body.

Installation Requirements:

R001 R120 R150 R170 R290

Expiry date:

31/01/2029

Model:

Cura Electrolytic Scale Reducer

Approval Holder:

Bes Ltd

Company Name

Bes Ltd

Address

Junction 6 Industrial Park Birmingham

Postcode

B6 7JJ

View All Listings by this Company

'JERLAC Bituminous sealer coat black'. Factory applied, black coloured Bitumen coating. Apply as per manufacturer's TDS reference 'BN433', dated '27/07/2023', revision '00'. Cure for 12 hours@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5021 Bituminous Based Products

Section Subtitle:

Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials containing petroleum or asphaltic bitumen are not approved for use on water-retaining structures with large surface:volume ratio such as lining of pipes, cisterns or water storage tanks in contact with wholesome water, but may be acceptable for use where there is only a small surface area in contact with the water – e.g. taps, valves and pipe connectors.

WRAS Approval Number:

240255047

Expiry date:

28/02/2029

Approval Holder:

M/S German Polymers and Coatings (PVTE) Limited

Company Name

M/S German Polymers and Coatings (PVTE) Limited

Address

No-18, Othivakkam Village Kumuzhi Panchayat, Chengalpet District, Pin-603202, Tami Nadu

Country

India

View All Listings by this Company

'Transpoxy Guard 472'. Factory applied, two-part, creamy white coloured epoxy resin coating. Mix base and hardener in a mass ratio of 4:1 and apply as per manufacturer's TDS dated 'January 2017'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2311569

Expiry date:

30/11/2028

Approval Holder:

Transocean Coatings

Company Name

Transocean Coatings

Address

Huygensstraat 3, 2652 XK, Berkel en Rodenrijs

Country

Netherlands

Phone

+3110 - 4134477

View All Listings by this Company