Range of screw down stop valves with brass bodies. All models incorporate a wheel type operating member. Maximum working pressure: 16.0 bar. Maximum operating temperature: 95°C.
Range of pilot operated electronic flow control valves having flow control facility intended to be controlled via solenoid valves, with auxiliary components including stainless steel tubing, cock valves, needle valve and a stainless-steel strainer. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of manually operated balancing valves (DZR Brass body). Maximum working pressure 20.0 bar. Maximum operating temperature 99ºC.
UV disinfection unit with stainless steel body and quartz sleeves. Maximum working pressure 3.0 bar. Maximum operating temperature 35°C.
Range of plastic water meter manifold adaptors incorporating plastic flow regulators and sampling adapter. Above ground use only. Maximum working pressure: 12.5 Bar. Maximum working temperature: 23°C.
'NF 131118'. Factory applied, grey coloured, two-part, water-based epoxy coating. Mix resin and curing agent in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V1', dated '20240423'. Cure for 60 minutes@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 864'. Factory applied, cream coloured, two-part Polyurethane coating. Mix parts A and B in a 66:34 volume ratio and apply as per manufacturer's TDS dated '26/11/2024'. Cure for 50 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM III/B-SR - Ramco Slag'. Factory applied, grey coloured Portland Slag Cement. Mix cement:sand:water in a 0.6:1.0:0.22 weight ratio and apply as per manufacturer's work instructions 'WP-08-05 I, issue no. 04, Rev. 0', dated '22.08.2024'. Cure for 24 hours at 27°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GM2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'GMSM01' dated '2024.11.16'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Wudu brand-NF 131118'. Factory applied, black coloured, two-component, water based epoxy coating. Mix in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V2', dated '20240821'. Cure for 1 hour@50°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 1015 of 1132
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
