Hansgrohe SE Approvals


WRAS Approval Number: 1807027

‘Hansgrohe Metris’ range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. These products are intended for connection to a specifically dimensioned installation set, (which is not supplied or covered under the scope of this approval). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

  • Section: 0510 Combination Tap Assemblies
  • Section Subtitle: Two hole, metal, single outlet, fixed.
  • WRAS Approval Number: 1807027
  • Expiry date: 31/07/2023
  • Size: Headwork base is 34mm OD (outside diameter). Spout inlet is ½” BSP (M).
  • Marking: Hansgrohe logo on operating member
  • Installation Requirements R001 R010 R040
  • Model
    Hansgrohe Metris Range: 31 085 xxx, 31 086 xxx, 31 251 xxx, 31 162 xxx & 31 163 xxx. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Manufacturer: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1807028

Range of overhead shower outlets with brass bodies in a variety of surface finishes, incorporating EPDM `O`-rings. The shower outlets also incorporate a plastic strainer. Maximum operating temperature 70°C.

  • Section: 1650 Shower Outlets
  • WRAS Approval Number: 1807028
  • Expiry date: 31/07/2023
  • Note: Open outlet use only.
  • Size: ½” BSP (M)
  • Marking: Hansgrohe on body
  • Installation Requirements R001 R040
  • Model
    27 468 xxx Hansgrohe Raindance Air Overhead Shower 27 471 xxx Hansgrohe Raindance Overhead Shower 27 472 xxx Hansgrohe Raindance Overhead Shower 27 476 xxx Hansgrohe Raindance Air Overhead Shower 27 478 xxx Hansgrohe Raindance Air Overhead Shower 27 492 xxx Hansgrohe Raindance Air Overhead Shower 27 493 xxx Hansgrohe Raindance Overhead Shower 27 494 xxx Hansgrohe Raindance Overhead Shower Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Manufacturer: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1807036

Range of concealed thermostatic shower mixers with brass bodies (various finishes), incorporating a ceramic disc diverter valve controlling the flow between two outlets. Temperature is controlled independently via a thermostatic cartridge with manual override button. The products are supplied with trim sets and operating members in a variety of finishes. The 15 708 xxx models have cube type operating members, the 15 714 xxx & 15 758 xxx models have single lever operating members. Both inlets incorporate an approved check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.

  • Section: 2010 Valves
  • Section Subtitle: Blending, thermostatic.
  • WRAS Approval Number: 1807036
  • Expiry date: 31/07/2023
  • Note: This approval does not include a shower hose and handset.
  • Size: ¾” BSP (F)
  • Marking: Hansgrohe on faceplate
  • Installation Requirements R001 R010 R040
  • Model
    15 708 xxx Ecostat E. 15 714 xxx Ecostat. 15 758 xxx Ecostat S. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Manufacturer: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1807037

Range of concealed thermostatic shower mixers with brass bodies (various finishes), incorporating a ¼ turn ceramic disc headwork controlling the flow. Temperature is controlled independently via a thermostatic cartridge with manual override button. The products are supplied with trim sets and operating members in a variety of finishes. The 15 708 xxx models have cube type operating members, the 15 714 xxx & 15 758 xxx models have single lever operating members. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.

  • Section: 2010 Valves
  • Section Subtitle: Blending, thermostatic.
  • WRAS Approval Number: 1807037
  • Expiry date: 31/07/2023
  • Size: ¾” BSP (F)
  • Marking: Hansgrohe on faceplate
  • Installation Requirements R001 R010 R040
  • Model
    15 707 xxx Ecostat E. 15 712 xxx Ecostat. 15 757 xxx Ecostat S. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Manufacturer: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1807038

Range of wall mounted, exposed, manual blending (shower) mixers with brass bodies (various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

  • Section: 2000 Valves
  • Section Subtitle: Blending, manually operated.
  • WRAS Approval Number: 1807038
  • Expiry date: 31/07/2023
  • Size: ½” x ¾” offset unions
  • Marking: Hansgrohe on operating member
  • Installation Requirements R001 R010 R040
  • Model
    14 161 xxx Hansgrohe Talis Classic. 32 620 xxx Hansgrohe Talis S. 32 640 xxx Hansgrohe Talis. 71 600 xxx Hansgrohe Logis. 71 262 xxx Hansgrohe Logis. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Manufacturer: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1807314

Single hole, single outlet (fixed) combination tap assembly with brass body (various finishes), incorporating a ceramic cartridge headwork with and single lever operating member. The spout outlet incorporates a plastic aerator which includes a 5.7l/min plastic flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

  • Section: 0450 Combination Tap Assemblies
  • Section Subtitle: Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
  • WRAS Approval Number: 1807314
  • Expiry date: 31/07/2023
  • Note: Claims for flow rate are made by the manufacturer and not considered part of the listing.
  • Size: Stainless steel braided PEX lined flexible hose assemblies incorporating ⅜” captive nut end connections.
  • Marking: Hansgrohe on operating member
  • Installation Requirements R001 R006 R009 R010
  • Model
    71 050 xxx Hansgrohe Novus Pillar tap 70 without waste set. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Factor: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1807332

‘Hansgrohe Novus’ range of wall mounted, manually operated shower blending valves with brass bodies (various finishes), incorporating ceramic cartridge headworks, and various single lever operating members. The outlet connection incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.

  • Section: 2000 Valves
  • Section Subtitle: Blending, manually operated.
  • WRAS Approval Number: 1807332
  • Expiry date: 31/07/2023
  • Note: This approval does not include a shower hose and handset.
  • Size: ¾” BSP (F) x ½” BSP (M) offset union connectors
  • Marking: Hansgrohe on operating member
  • Installation Requirements R001 R010 R040
  • Model
    Hansgrohe Novus Range: 71 926 xxx, 71 360 xxx & 71 060 xxx. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Factor: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1807333

‘Hansgrohe Novus’ single hole, single outlet (fixed) combination tap assembly with brass body (various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.

  • Section: 0450 Combination Tap Assemblies
  • Section Subtitle: Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
  • WRAS Approval Number: 1807333
  • Expiry date: 31/07/2023
  • Size: Stainless steel braided TPSiV lined flexible hose assemblies incorporating ⅜” captive nut end connections.
  • Marking: Hansgrohe on operating member
  • Installation Requirements R001 R006 R009 R010
  • Model
    Hansgrohe Novus - 71 322 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Factor: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1807339

Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a flow regulator and plastic aerator. Model 71 126 000 is also supplied with a lever operated pop-up waste. Maximum working pressure 10 bar. Maximum working temperature 60°C.

  • Section: 0470 Combination Tap Assemblies
  • Section Subtitle: Single hole, metal, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
  • WRAS Approval Number: 1807339
  • Expiry date: 31/07/2023
  • Size: Stainless steel braided PEX lined flexible hose assemblies incorporating ⅜” captive nut end connections.
  • Marking: Hansgrohe on body
  • Installation Requirements R001 R006 R009 R010
  • Model
    Hansgrohe Novus: 71 126 xxx & 71 128 xxx. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Factor: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1707113

Range of concealed flow control valves with brass bodies (various finishes), incorporating either non-rising spindle or ¼ turn ceramic disc (16 973 180 only) headworks. Valve models are for use with trim kits utilising various operating members (see below). Kits are available in various finishes (denoted by xxx). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

  • Section: 2000 Valves
  • Section Subtitle: Blending, manually operated.
  • WRAS Approval Number: 1707113
  • Expiry date: 31/07/2022
  • Size: 15 974 180 & 15 973 180: ½” BSP (F) 15 970 180: ¾” BSP (F)
  • Marking: Hansgrohe & direction of flow arrow on body
  • Installation Requirements R001 R040
  • Model
    Concealed Valves: 16 974 180, 16 973 180 & 16 970 180 Trim Kits: 10 970 xxx Axor Starck (lever), 10 972 xxx Axor Shower (lever), 10 974 xxx Axor Starck X (lever), 11 960 xxx Axor Urquiola (cubed), 12 771 xxx Axor Starck Organic (dome), 16 871 xxx Axor Montreux (cross top), 16 872 xxx Axor Montreux (lever), 17 960 xxx Axor Carlton (lever), 17 965 xxx Axor Carlton (cross top), 18 770 xxx Axor Massaud (dome), 19 971 xxx Axor Bouroullec (dome), 34 960 xxx Axor Citterio M (lever), 34 980 xxx Axor Citterio M (three prong), 36 771 xxx Axor Citterio E (cross top), 38 976 xxx Axor Uno (dome), 39 960 xxx Axor Citterio (lever) & 39 965 xxx Axor Citterio (cross top). Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
  • Factor: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company
  • Manufacturer: Hansgrohe SE
    Company Name
    Hansgrohe SE
    Address
    Auestrasse 5 - 9, 77761 Schiltach
    View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 7 of 32