Range of combination valves consisting of an in-line adjustable pressure reducing valve (between 1.5 and 6.0 bar) and a pressure relief valve, with DZR Brass bodies, EPDM `O`-rings and an EPDM diaphragm. CWIC110004 model - Pressure reducing valve pre-set at 3.5 bar and pressure relief valve set at 6.0 bar. CWIC200055 model - Pressure reducing valve pre-set at 3.0 bar and pressure relief valve set at 4.5 bar. The product incorporates a stainless-steel mesh and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum supply pressure 16.0 bar. Outlet pressure range 1.5 bar to 6.0 bar (both models). Maximum operating temperature 20°C.
Range of UV water treatment units with stainless steel bodies and quartz sleeves. Maximum operating pressure 8.6 bar. Cold water use only.
'FLOGUL 645B Bleu 5005'. Factory applied, blue coloured synthetic resin coating. Apply as per manufacturer's Technical Data Sheet, version '26/01/2023'. Cure for 7 days@20°C. For use with water up to 23°C.
'BFSC RIZHAO S&M&B DN 22'. Factory applied, grey coloured Blast Furnace Slag Cement Mortar Lining. Mix cement and sand in a weight ratio of 1:2.2. Mix this with water in a 0.46:1 weight ratio. Apply as per manufacturer's TDS '1008', dated '20221008'. Cure for 9 hours at 60°C & 95% humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SATHAVAHANA Ordinary Portland Cement'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SATHAVAHANA Sulphate Resistant Portland Cement'. Factory applied, grey coloured Sulphate Resistant Portland Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SATHAVAHANA Portland Slag Cement'. Factory applied, grey coloured Portland Slag Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JHSW-8604 Pipeline Heavy Duty Anti-Corrosion Polyurethane Coating'. Factory applied, two-component, pale yellow coloured polyurethane coating. Mix parts A & B in a 1:1 volume ratio and apply as per manufacturer's Product Information, issue date '6/1/2022'. Cure for 1 minute@25°C and then 7 days @23. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline DT-750'. Factory applied, grey coloured, two component epoxy coating consisting of a base and curing agent. Mix the base and curing agent in a 3:1 volume ratio and apply as per manufacturer’s TDS ‘April 2010’. Cure for 7 days@25°C. For use with water up to 45°C. In September 2025, ‘Pentaline DT-750 Blue' was added to the approval. Factory applied, blue coloured, two component epoxy coating consisting of a base and curing agent. Mix the base and curing agent in a 3:1 volume ratio and apply as per manufacturer’s TDS ‘April 2010’. Cure for 7 days@30°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'VIMPOTABLE 34 EPOXY PAINT'. Factory applied, two-component, red coloured epoxy coating. Mix Parts A & B in a 3:1 volume ratio and apply as per manufacturer's Technical Bulletin 'VP/02', issue date '01.01.2021'. Cure for 7 days@50°C. For use with water up to 45°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPL Gold Portland Slag Cement'. Grey coloured, factory applied Portland Slag cement. Mix cement, sand & water in a 1:1.4:0.35 mass ratio. Apply as per manufacturer's work instructions document code 'WI/SP/FINC&B/02', issue '06'. Cure for 24 hours@27°C, 70% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's product information dated 'August 16,2022'. Cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/013', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Sulphate Resisting Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/014', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Blast Furnace Slag Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/012', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RMD 7080/xx, RUD 2230/xx, RMD 7100/xx, RUD 2247/xx, RUD 2273/xx, RMD 7061/xx'. 'xx' denotes the customer and can be replaced with numbers between 01 & 99. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions '0703231010' dated 14.03.23. Cure for 10 minutes@860°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'PPELXS314G20NA'. Beige coloured, injection moulded PPE material. For use with water up to 85°C.
'PTFE G405'. White coloured, extruded, PTFE ring. For use with water up to 85°C.
3M™ Dyneon™ TF 1620, TF 1641, TF 1645, TF 1702, TF 1750, TFM 1600, TFM 1635, TFM 1700, TFM 1705, TF 4103K, TF 4105K, and TFM 4105K. White coloured, pressed+sintered PTFE materials. 3M™ Dyneon™ TF 2021Z, TF 2025Z, TF 2029Z, TF 2035Z, TF 2053Z, TF 2071Z, TF 2072Z, TF 2073Z, TFM 2001Z, TFM 2033Z and TFM 2070Z. White coloured, extruded PTFE materials. 3M™ Dyneon™ TF 4215 & TF 4303. Black coloured, pressed+sintered PTFE materials. For use with water up to 85°C.
‘DEWALT PV60-PRO’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions rev. 1, version 16/01/2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 98 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
