`Maxxam PP Flow Meter Insert`. Off-white coloured, injection moulded polypropylene flow meter insert. For use with water up to 23°C. From September 2023, the component is for use with water up to 85°C.
'Moplen EP 300 K PP Cover'. White coloured, translucent, injection moulded polypropylene cover. For use with water up to 85°C.
'Magnum 3G Compression Fitting Body'. Black coloured, injection moulded polypropylene fitting body. For use with water up to 60°C.
'Borstar RA140E'. Natural (appears white coloured, translucent) injection moulded or extruded polypropylene material. For use with water up to 85°C.
'KF Polymer T-1100'. Transparent (un-pigmented), injection moulded, polyvinylidine fluoride material. For use with water up to 85°C.
'EP80/2 BLK 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Tested in-radius size 1.5mm. For use with water up to 85°C.
EP80/2 BLK 'O' rings & gaskets. Black coloured, injection moulded EPDM 'O' rings & gaskets. Shore hardness 80. Tested in-radius size 1.5mm. . For use with water up to 85°C.
`B1-4773`. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
`70 EP 111 p`. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
EP0E7001P-WRC. Black coloured, compression moulded EPDM sheet material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'E7008W'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.05mm. For use with water up to 85°C.
'WN60/1 BLK 'O' rings'. Black coloured, injection moulded NBR 'O' rings. Shore hardness 60. Tested in-radius size 1.31mm. For use with water up to 60°C.
`WN 22/1/9 BLK` 'O' rings. Black coloured, injection moulded, nitrile rubber 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 65°C.
'kSil GP40 - GP-70'. Extruded, silicone rubber material available in translucent (which appears off-white), black, white, red and blue colours. Shore hardness between 40 & 70. Tested in-radii sizes between 0.15mm & 6.0mm. For use with water up to 85°C.
'Griffon WDF-05'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6311380 20200708'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Beaulon P5250N Grey & Beaulon P5250N White'. Compression moulded, thermoplastic Polybutene materials. For use with water up to 85°C.
'Hytrel® 6359FG & 4068FG'. Cream coloured, injection moulded, thermoplastic polyester elastomeric materials. For use with water up to 85°C.
`Aqua Clean Mera` range of bidets incorporating an electronically operated seat, flow is controlled by solenoid valve and discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar. Cold water supply only.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves (housed in a control box) activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically operated, tap assemblies (chromium plated brass). Flow is controlled via solenoid valve and actuated by a touch sensor. The spout outlets incorporate a plastic aerator, supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Page 10 of 577
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
