'SABIC® Vestolen A RELY 5922R 10000'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
'P901BK'. Black coloured, extruded HDPE material. For use with water up to 23°C.
3M™ Dyneon™ TF 1620, TF 1641, TF 1645, TF 1702, TF 1750, TFM 1600, TFM 1635, TFM 1700, TFM 1705, TF 4103K, TF 4105K, and TFM 4105K. White coloured, pressed+sintered PTFE materials. 3M™ Dyneon™ TF 2021Z, TF 2025Z, TF 2029Z, TF 2035Z, TF 2053Z, TF 2071Z, TF 2072Z, TF 2073Z, TFM 2001Z, TFM 2033Z and TFM 2070Z. White coloured, extruded PTFE materials. 3M™ Dyneon™ TF 4215 & TF 4303. Black coloured, pressed+sintered PTFE materials. For use with water up to 85°C.
'Art. 0985077200'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'80EP251p 'O' ring'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 0.89mm. For use with water up to 85°C.
‘07096-80 gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 80. Tested in-radius size between 0.9mm & 1.75mm. For use with water up to 85°C.
'7751 'O' rings'. Blue coloured, compression moulded VMQ 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.
'S70C'. Off-white coloured (translucent), compression moulded silicone 'O' rings. Shore hardness 70. Tested in-radius size between 0.89mm & 3.5mm. For use with water up to 85°C.
'GW'. White coloured (opaque), Polyamide synthetic fibre thread impregnated with an inert paste. Apply as per manufacturer's TDS issued on '09/02/2023', version '1'. For use with water up to 85°C.
'Loctite SI 5331 (known as 'Loctite 5331')'. White coloured silicone thread sealant. Apply as per manufacturers technical data sheet ‘reference 1.7’ dated May 2014. Cure for 96 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 719 PVCu Clear Solvent Cement'. Clear, colourless solvent cement. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C(±2°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘M930F, M330F, M630F, M730F, M410F & M710F’. Beige coloured, injection moulded polyketone materials. For use with water up to 85°C.
Range of wall mounted electric showers (various finishes). The product incorporates a solenoid valve controlling the flow. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled via a manual operating single lever on body. The inlets hose incorporates stainless steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection). The spout outlet incorporates a plastic aerator and the product is supplied with metal backnuts. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of wall mounted single-hole, single outlet, fixed electronically controlled combination tap assemblies (chrome plated brass), incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
Concealed WC dual flushing cistern with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Maximum working pressure - 10 Bar Maximum operating temperature – Cold water use only.
Range of inlet control valves with DZR brass bodies incorporating a pressure reducing valve (set at 1.5, 1.8. 2.0, 2.1, 3.0 or 3.5 depending on model) and a pressure relief valve (set at 3.0, 3.5, 4.5, 5.0. 6.0 or 8.0 depending on model. All models incorporate a stainless-steel mesh and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model CWIC355040 comes supplied with a tundish. For use with copper pipe to BS EN 1057, PB pipe (with inserts) to BS EN 7291-2:2010 and PEX pipe (with inserts) to BS EN 7291-3:2010. Maximum working pressure 16.0. Maximum operating temperature of 25°C.
Range of tundishes with black plastic bodies. The products comply with the requirements of an air gap to drain.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electrically heated catering water boilers with inlet supply controlled via a solenoid valve. The water is discharged via a self-closing tap with single lever operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Page 89 of 214
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
