‘Nitocote EP 405’. Site applied, two-part,white coloured epoxy based Waterproofing coating. Mix 3.1 litres of the base with 0.9 litres of hardener and apply as per manufacturer’s TDS ‘UAE/0228/22/K’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

250755057

Expiry date:

31/07/2030

Approval Holder:

Al Gurg Fosroc LLC

Company Name

Al Gurg Fosroc LLC

Address

PO Box 657, 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Area, Dubai

Country

United Arab Emirates

View All Listings by this Company

'Belzona 1331'. Grey coloured, site applied, two-component epoxy coating. First coat: Mix Belzona 1331 (white, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure for 6-8 hours@10°C or 3-4 hours@30°C then apply: Second coat: Mix Belzona 1331 (grey, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure in accordance with manufacturer’s IFU ’06-03-19’, ‘Completion of the Molecular Reaction’ table, ‘Full mechanical/thermal loading or water immersion’. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

250855035

Expiry date:

31/08/2030

Approval Holder:

Belzona Limited

Company Name

Belzona Limited

Address

Claro Road, Harrogate, Yorks.

Postcode

HG1 4AY

Phone

+44 1423 567641 Fax: 01423 505967

View All Listings by this Company

'Belzona 5811DW2 (grey)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (grey, opaque glossy paste) with Part B (orange, transparent liquid) in a 4:1 mass ratio and apply as per manufacturer’s IFU ’16-03-19’. Cure for 4 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

250855036

Expiry date:

31/08/2030

Approval Holder:

Belzona Limited

Company Name

Belzona Limited

Address

Claro Road, Harrogate, Yorks.

Postcode

HG1 4AY

Phone

+44 1423 567641 Fax: 01423 505967

View All Listings by this Company

'Grivory GVN-5H black 9915'. Black coloured, injection moulded PA 66 + PA 6I/X-GF50 material. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

250855037

Expiry date:

31/08/2030

Approval Holder:

EMS-CHEMIE AG

Company Name

EMS-CHEMIE AG

Address

Via Innovativa 1, CH-7013 Domat/Ems

Country

Switzerland

Phone

+41 81 632 78 78

General Email

welcome@emsgrivory.com

View All Listings by this Company

'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

251155013

Expiry date:

30/11/2030

Approval Holder:

POLYTECHNYL S.A.S. Member of DOMO Chemicals

Company Name

POLYTECHNYL S.A.S. Member of DOMO Chemicals

Address

Usine de Belle Etoile, Avenue Albert Ramboz, 69190 SAINT-FONS

Country

France

View All Listings by this Company