‘Quattroselect’ range of chemical dosing units incorporating a lockable self-closing trigger assembly and a self-closing bottle filler assembly which control the flow. The products are supplied with an approved double check valve assembly at the inlet (suitable for backflow prevention against fluid category 3). Maximum working pressure 5.8 bar. Cold water use only.

Section:

0970 Dosing Equipment

Section Subtitle:

Fittings in this section have been judged only against the requirements of The Water Supply (Water Fittings) Regulations 1999 (England and Wales), The Water Supply (Water Fittings) (Scotland) Byelaws 2014 or The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009. The decision of the Scheme to list them is not to be taken as any guide as to their effectiveness to do the job for which they have been designed

WRAS Approval Number:

2110700

Size:

¾” BSP (M)

Marking:

Quattroselect on hose trigger. Diversey on label on door panel. Quattroselect on front panel. Other product info inside door panel.

Installation Requirements:

R001 R160 R040

Expiry date:

31/10/2026

Proviso:

Not suitable for use with chemicals greater than a fluid category 3 risk.

Model:

1219424 – QuattroSelect Pouch air gap CW 1219425 – QuattroSelect Pouch safe gap CW 1211418 – QuattroSelect Pouch air gap

Approval Holder:

Diversey Europe Operations BV.

Company Name

Diversey Europe Operations BV.

Address

De Boelelaan 32, 1083 HJ Amsterdam, Netherlands

View All Listings by this Company

Range of capillary end feed bronze fittings for use with copper tube (manufactured to BS EN 1057). 15mm – 54mm fittings have a maximum working pressure of 25.0 bar. 67mm – 108mm fittings have a maximum working pressure of 16.0 bar. Maximum operating temperature 100°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2105306

Note:

Above ground use only.

Size:

15mm – 108mm.

Marking:

Kembla & size on body.

Installation Requirements:

R001

Expiry date:

31/05/2026

Model:

FEN – Female 90° Elbow 15mm x 1/2” code FEN015 22mm x 1/2” code FEN02215 22mm x 3/4" code FEN022 28mm x 1” code FEN028 MEN – Male 90° Elbow 15mm x 1/2" code MEN015 FTE – Female Tee 22mm x 1/2" code FTE02215 35mm x 3/4" code FTE03522 42mm x 3/4" code FTE04222 42mm x 1” code FTE04228 54mm x 3/4" code FTE05422 54mm x 1” code FTE05428 FCE – Female Cross Tee 35mm x 3/4" code FCE03522 42mm x 3/4" code FCE04222 42mm x 1” code FCE04228 54mm x 3/4” code FCE05422 54mm x 1” code FCE05428 FCC – Female Coupler 15mm x 1/2" code FCC015 22mm x 3/4” code FCC022 28mm x 1” code FCC028 35mm x 1-1/4” code FCC035 42mm x 1-1/2” code FCC042 54mm x 2” code FCC054 67mm x 2-1/2” code FCC067 BTR – Reducing Coupling 22mm x 1/2" code BTR022 MCC – Male Coupler 15mm x 1/2" code MCC015 22mm x 3/4” code MCC022 28mm x 1” code MCC028 35mm x 1-1/4” code MCC035 42mm x 1-1/2” code MCC042 54mm x 2” code MCC054 67mm x 2-1/2” code MCC067 76mm x 3” code MCC076 108mm x 4” code MCC108

Approval Holder:

Kembla (HK) Limited

Company Name

Kembla (HK) Limited

Country

China

Phone

+852 2833 9308

General Email

charles.tam@kembla.com.hk

View All Listings by this Company

WC dual flush drop valve with plastic body silicone and rubber seal. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold Water Use Only.

Section:

1305 Valves

Section Subtitle:

Flushing valve(s) for WC Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

2104010

Size:

2" BSP (M)

Marking:

Xiamen NAT Plumbing Inc. logo (‘NAT’) on top of valve body.

Installation Requirements:

R001 R571

Expiry date:

30/04/2026

Model:

NB210

Approval Holder:

XIAMEN NAT PLUMBING INC.

Company Name

XIAMEN NAT PLUMBING INC.

Address

3RD FLOOR, BLDG.4, WEST HOUXIANG ROAD, HAICANG, XIAMEN, P.R.CHINA H

Phone

+86-592-6538317

View All Listings by this Company

Manufacturer:

XIAMEN NAT PLUMBING INC.

Company Name

XIAMEN NAT PLUMBING INC.

Address

3RD FLOOR, BLDG.4, WEST HOUXIANG ROAD, HAICANG, XIAMEN, P.R.CHINA H

Phone

+86-592-6538317

View All Listings by this Company

WC dual flush drop valve comprising of a plastic body and silicone seating washer. The valves are operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water only.

Section:

1305 Valves

Section Subtitle:

Flushing valve(s) for WC Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

2104028

Size:

2” BSP (M)

Marking:

Model and UNITOP logo (‘Unitop’, where the ‘o’ is a water droplet) on valve body.

Installation Requirements:

R001 R571

Expiry date:

30/04/2026

Model:

A31-04

Approval Holder:

Xiamen Unitop Plumbing Technology Co Ltd

Company Name

Xiamen Unitop Plumbing Technology Co Ltd

Address

No. 1 Building No. 469 Jinyuan West Road Xinglin

Country

Jimei District

Phone

+86 592 6379968

View All Listings by this Company

Manufacturer:

Xiamen Unitop Plumbing Technology Co Ltd

Company Name

Xiamen Unitop Plumbing Technology Co Ltd

Address

No. 1 Building No. 469 Jinyuan West Road Xinglin

Country

Jimei District

Phone

+86 592 6379968

View All Listings by this Company

Range of WC flapper valves with a silicone seal, ABS body and internal overflow. The device is operated via a plastic chain to be connected to a cistern handle. Cold water use only.

Section:

1305 Valves

Section Subtitle:

Flushing valve(s) for WC Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

2104042

Size:

2” BSP (M)

Marking:

WDI, ECO and B1017 on body.

Installation Requirements:

R001 R571

Expiry date:

30/04/2026

Model:

B1017-G. B1017-U.

Approval Holder:

ECO (Xiamen) Technology INC.

Company Name

ECO (Xiamen) Technology INC.

View All Listings by this Company

Manufacturer:

ECO (Xiamen) Technology INC.

Company Name

ECO (Xiamen) Technology INC.

View All Listings by this Company