Section Code 1610 : Wholesome water use.
Back To Directory SectionsRange of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.
Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.
CM(E) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Maximum operating parameters: Cast iron models: Maximum working pressure 6.0 bar @ 90°C. Maximum working pressure 10.0 bar @ 40°C. Stainless steel models (not self-priming variants): Maximum working pressure 10.0 bar @ 99°C. Maximum working pressure 16.0 bar @ 90°C. Stainless steel self-priming models (CM(E) 1, 3 & 5 (AISI 304) only): Maximum working pressure 10.0 or 16.0 bar @ 60°C.
Range of multistage pumps with stainless steel bodies Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. Maximum operating temperature 35°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of electric water pumps, with stainless steel bodies, shaft and either stainless steel or plastic impellors. Maximum working pressure 8.5 Bar. Maximum operating temperature: See models.
Range of self-priming electric booster pumps with plastic bodies incorporating plastic impellers with variable speed settings, and a non-return return valve (not suitable for backflow protection). Maximum working pressure 4.5 Bar Maximum operating temperature 50.0°C
FVC & FVS Ranges of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.
Range of multistage pumps with stainless steel bodies Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of electric water pumps, with stainless steel bodies, shaft and either stainless steel or plastic impellors. Maximum working pressure 8.5 Bar. Maximum operating temperature: See models.
Range of multistage pumps with stainless steel bodies Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
MBC 12-22WM & MBC 12-28WM models are wall mounted mains supply booster sets. They are supplied with two spherical isolation valves, a spherical bypass valve and two single check valve assemblies (suitable for backflow protection against Fluid Category 2). The check valve assemblies are to be installed in accordance with the manufacturers instructions, one upstream of the pump inlet and one after the bypass valve. The booster pump incorporates a plastic strainer on the inlet and a plastic flow regulator on the outlet and is housed within a wall mounted cabinet. MJ3 VM & MJ3 HM models are mains supply booster sets intended to be mounted on an expansion vessel (not supplied as part of the approval). They comprise of a pump, a suction and discharge manifold with bypass arrangement, and a spherical bypass valve which incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The booster pump incorporates a plastic strainer on the inlet and a plastic flow regulator on the outlet. Maximum working pressure: 6.0 bar. Maximum operating temperature: 35oC.
Range of booster pumps with stainless steel inlet manifolds, plastic bodies and impellers. The product incorporates a non-return valve. The ESYBOX MAX single models are also supplied with an optional 2” BSP (M) x 1¼” BSP (F) plastic inlet adaptor. Maximum working pressure 12.0 bar. Cold water use only.
Circulation pumps with either bronze or stainless pump bodies and a plastic impeller. Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C.
Range of rotary vane pumps with either brass, stainless-steel or plastic bodies, stainless steel impellor and EPDM ‘O’ rings. Maximum working pressure 20 Bar. Cold water use.
Page 9 of 9
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
