Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'Challenger ABS Fittings'. Light grey coloured, injection moulded ABS fittings. For use with water up to 23°C.
'Deep High Build Liquid Bitumen Paint'. Factory applied, black coloured bitumen paint. Apply and cure as per manufacturer's instructions reference 'DI/BP/2021/011' dated April 15, 2021. For use with water up to 60°C.
'P658RC & CY10C washers'. P658RC is a black coloured, polyester resin impregnated carbon washer. CY10C is a dark grey coloured, phenolic resin impregnated carbon washer. For use with water up to 85°C.
'SC4'. Factory applied, clear PTFE coating, intended for use with `O` rings, seals & gaskets. Apply as `Superior Group Quality Management System Procedure Reference 8.6’ referenced in document `LDAP-008 issue 1` released 01/05/2020. For use with water up to 85°C
`Suns-02`. Grey coloured, factory applied cement mortar. Mix, apply and cure as per user instructions 'doc: SUNS-U110320, version B` dated 2015-12. Cure for 24 hours@25°C. Between 1st May 2021 and 30th March 2022, the cement mortar is suitable for use with water up to 23°C. Between 31st March 2022 and 31st May 2026, the cement mortar is suitable for use with water up to 60°C
`Jin Dapeng WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions 'version no: JDP2015-01' dated 24th November 2015. For use with water up to 85°C.
'HSL-0588-3 Silicon Coating'. Factory applied, translucent silicon coating. Apply and cure as per manufacturer's instructions version 'BLT19.05 A'. For use with water up to 85°C.
'Unitech DIP Sulphate Cement'. Factory applied, grey coloured sulphate cement. Mix as per work instructions issue no. 'QAP-MOS-UNITECH 212-13- rev1', dated 21st December 2020. Cure for 6 hours@40°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JIZJ-2'. Factory applied, grey coloured Sulphate resistant Portland cement. Mix cement, sand & water in a 1:1.7:0.55 mass ratio. Cure for 5.5 hours@65°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'BGDI01 Sulphate Resistant Cement & BGDI02 Portland Cement'. Factory applied, grey coloured cements. Mix 1 part cement, 2 parts sand and 0.25 parts water. Cure for 10 hours@23°C. For use with water up to 65°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'PMSP5105-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'PMSP5065-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'Parasakti Sulphate Resisting Portland Cement'. Factory applied, grey coloured Sulphate Resistant cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Rashmi Cement 43 Grade OPC'. Factory applied, grey coloured Ordinary Portland cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MEKCOAT Liquid Membrane Coating'. Factory applied, two-component, blue coloured polyurethane coating. Mix in a 1:1 volume ratio. Cure for 24 hours@23-24°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'5017 Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions issued January 2020, 'V7.2'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CeramycGuard for use with QuartzSeal'. Site applied, white coloured (once mixed) polymer based concrete surface treatment. 'CeramycGuard’ is a three-component base coat comprising of Part A (clear liquid), Part B (grey powder) & Part C (clear liquid). Mix Parts A, B & C in a volume ratio. Rest for two minutes, apply as per manufacturer's instructions for use 'version 2' dated 'April 2021' and then cure for 24 hours@21°C. ‘QuartzSeal' is a white coloured, single-component topcoat. Apply as per manufacturer's instructions for use 'version 2' dated 'April 2021'. Cure for 7 days@21°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
`Fernox Powerflow Flux`. White coloured paste flux. For use with water up to 85°C.
Page 9 of 160
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
