'C40'. White coloured, extruded polyethylene pipe. For use with water up to 85°C.
`Polyfill PPH TS15040D Natural`. Natural (appears grey in colour), injection moulded polypropylene material. For use with water up to 85°C.
`Polyfill PPH T8020 1035 Grey & Polyfill PPHC T8040 1017 Grey'. Grey coloured, injection moulded polypropylene materials. Between February 2022 and September 2022, 'Polyfill PPHC T8040 1017 Grey' was for use with water up to 23°C. Between October 2022 and February 2027, 'Polyfill PPHC T8040 1017 Grey' is for use with water up to 85°C. 'Polyfill PPH T8020 1035 Grey' is for use with water up to 85°C.
'7PD1612 washers'. Black coloured, extruded NBR rubber washers. Tested in-radius size 1.4mm. Shore hardness 70. '7PD1612 'O' rings'. Black coloured, injection moulded NBR rubber `O` rings. Tested in-radius size 0.9mm. Shore hardness 70. Both for use with water up to 60°C.
‘Silopren LSR 2030, 2040, 2050, 2060, 2070 & 2080’. Natural (appears clear), compression moulded silicone rubbers with a shore hardness between 30 and 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Adey MCXS Clear'. Clear, silicone sealant. Apply as per manufacturer's technical data sheet 'issue 1' dated 03/03/2022. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikasil DW Trans'. Site applied silicone sealants available in transparent (CO0 transparent), grey (RA1 7004) or black (CO4 Schwarz). Apply as per manufacturer's instructions Product Data Sheet 'April 2022, Version 04.01'. Cure for 24 hours@7°C. The transparent (CO0 transparent) and grey (RA1 7004) sealants are for use with water up to 85°C. The black (CO4 Schwarz) sealant is for use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Tangit PVC-U Plus'. Light yellow (straw) coloured, solvent cement. Apply as per manufacturer's TDS 'Tangit PVC-U PLUS TDS 070917 EN'. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Bidet seat assembly with the flow controlled by a sensor actuated solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 1.75 bar. Maximum operating temperature 45°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Page 78 of 652
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
