'XFGJ-2'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cepox P05/95'. Factory applied, two part, yellow coloured epoxy coating. Mix and apply as per Technical Data Sheet dated 19/11/2021. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kerjiwal SRC'. Factory applied, grey coloured Sulphate Resisting Cement. Mix cement, sand & water in a volume ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Belzona 1321`. Site applied, two-part, epoxy amine coating available in grey or blue colours. Mix base and hardener in a 11:1 mass ratio. Apply and cure as per manufacturer’s IFU ‘FN10026’, publication number ’02-09-21’. For use with water up to 23°C. These materials are only approved for the mixing conditions that appear on the approval. If the mixing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikalastic®-6100 FX White’ (formerly known as ‘MasterSeal 6100 FX White’) ‘Sikalastic®-6100 FX Grey’ (formerly known as ‘MasterSeal 6100 FX Grey’. Site applied, two-component cementitious coating. Mix ‘Sikalastic®-6100 FX White’ (Coat 1) with water in a mass ratio of 15:5.6. Apply and cure for 1 day@5°C before applying Coat 2. Mix ‘Sikalastic®-6100 FX Grey’ (Coat 2) with water in a mass ratio of 15:5.6. Apply and cure for 5 days@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tesnit BA-60'. Orange coloured aramid fibre/NBR gasket material. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
`Novapress 260`. Green coloured, compressed fibre material (bound with NBR), manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Acquablu Hose'. Extruded hose comprising of a white coloured (transparent) polyethylene inner layer, off-white coloured chlorobutyl second layer, rayon reinforcement layer and blue coloured bromobutyl outer later. For use with water up to 60°C.
'TUCAI WRAS EPDM hose'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 0.68mm. For use with water up to 70°C.
'Super Lube'. Colourless (transparent) lubricant. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Ultramid A3EG7 FC Aqua Uncoloured'. Natural (appears beige), injection moulded, PA66 polyamide material. For use with water up to 65°C.
'Badadur PBT8 GK30 Graphit 371'. Grey coloured, injection moulded PBT material. For use with water up to 65°C.
'Avaspire AV-621 NT'. Natural (appears beige, opaque), injection moulded PEEK material. For use with water up to 85°C.
'Aion MDPE Pipe'. Blue coloured, extruded MDPE pipe. For use with water up to 65°C.
'Aion HDPE Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 65°C.
'CONTINUUM DGDA-2610 BK'. Black coloured, compression moulded HDPE (PE100) material. For use with water up to 23°C.
'TASNEE 100 Black'. Black coloured HDPE material manufactured in Saudi Arabia and Germany, for injection moulding and extrusion purposes. For use with water up to 60°C.
'TORELINA A673MWRB'. Dark grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Floraseal'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
Page 70 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
