Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork controlling the flow with dome operating member incorporating a manual override button. The temperature is controlled by a thermostatic cartridge with dome or cube type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of pilot operated, adjustable, pressure reducing control valves, incorporating stainless steel bodies & strainers and EPDM ‘O’ rings & diaphragm. Auxiliary components include stainless steel tubing and isolation valves. The product is available with the following adjustable outlet pressures: 0 - 3.0 bar (silver spring), 1.0 - 8.0 bar (black spring), 1.0 - 16.0 bar (red spring). Maximum supply pressure 16.0 bar. Maximum operating temperature 65°C.
Pressure relief valve with a plastic body and EPDM diaphragm with manual easing gear. Pre-set at 3.0 bar. Model 31030030 is pre-set at 2.5 bar. Model 31030070 is pre-set at 4.5 bar. Maximum operating temperature 90°C.
Range of latching and non-latching solenoid valves with a plastic body (all models, except for 07230017 & 07230018 models added September 2023) and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Lever operated spherical valve with brushed chrome brass body, EPDM O-rings and PTFE gaskets. The valve incorporates a stainless steel filter with EPDM O-ring and brass filter plug. The compression connection is to be used with for polyethylene pipe PE100 to EN12201. Maximum working pressure 25.0 bar. Cold water use only.
Range of spherical valves with brass (CW617N) or DZR brass (CW511L) bodies (chrome plated, nickel plated or without plating - see model), chrome plated brass ball and a range of different operating members (see model). Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ball valves with nickel plated brass bodies, chrome plated brass ball, PTFE seats, and either lever or T handle operating members (see models). Maximum working pressure 16.0 to 64.0 Bar (Size & model dependant, see models) Maximum working temp 85°C
Range of gate valves with brass bodies and wedge with either a lock shield or non-rising spindle operating mechanism for use with copper pipe (manufactured to EN 1057). Maximum working pressure 6.0 Bar Maximum operating temperature 95.
Range of gate valves with a non-rising spindle and a handwheel operating member with a brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass bodies and bonnets and EPDM seats. Maximum working pressure 20.0 bar. Cold water use only.
Range of screw down angle valves with brass bodies (chromium plated) and NBR ‘O’-rings with a dome type operating member. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperatures: model 510052 = 95°C and model 510060 = 85°C.
'DURACON® M25-44 WK2001, M90-44 WK2001 & M270-44-WK2001'. White coloured, injection moulded POM materials. For use with water up to 85°C.
'MAT901 & MAT902'. In June 2025 ‘MAT901IT & MAT902IT’ washers were added to the approval. Black coloured carbon/PTFE washers manufactured by pressing. For use with water up to 85°C.
'A-95 sealing plate'. White coloured, compression moulded sealing plate. For use with water up to 85°C.
'AO-96 Sealing Ring'. Black coloured, compression moulded, ceramic sealing ring. For use with water up to 85°C.
'Eurokote® 448 Bleu 5005 & Eurokote® 448 Bleu 5002'. Factory applied, blue coloured, two-part epoxy coatings consisting of a resin and hardener. Mix resin and hardener in a 1:1 volume ratio and apply as per manufacturer's technical data sheet version dated '29/08/17'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'S' epoxy powder coating. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'SNC-EP09V1 - date 2009/12/1'. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote 468 Thixo Brun Rouge'. Factory applied, red/brown coloured, two-part epoxy coating consisting of a resin and hardener. Mix resin and hardener in a weight ratio of 77:23 and apply as per manufacturer's Data Sheet dated '10/05/2019'. Cure for 10 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 451 A – CP 573 B ITT Lowara'. Factory applied, blue coloured cationic resin coating. Apply as per manufacturer's technical data sheet 'LT/I-21-090' dated 'Sep 9, 2021'. Cure for 20 minutes@180°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 69 of 207
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
