Range of undercounter water chillers with a stainless-steel cooling tank including a drain outlet. Maximum working pressure 3.0 Bar. Maximum operating temperature 38°C.
Range of combined isolation and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-metallic materials and components comply with BS6920 at 65°C
'PCBIT III HIGHBUILD'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's instructions for use, reference 'PCC/ PC 820' dated 27.11.2023. Cure for 5 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RAX Cement Mortar'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instructions 'WI-PRD-08', rev. '00', dated '01.02.2023'. Cure for 24 hours@28°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Valcoat Blue'. Factory applied, blue coloured epoxy coating. Pre-heat the substrate and apply as per manufacturer's TDS with issue '01.04.2023'. Post-cure for 5-7 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'TM-cement-01'. Factory applied, grey coloured cement. Mix sand/cement/water in a weight ratio of 1.7:1.0:0.74 and apply as per manufacturer's instructions 'TM20231122-A0', dated 2023-11-22. Cure for 6 hours@25°C (±2°C). Between November 2023 and November 2024, the material was for use with water up to 23°C. Between December 2024 and November 2028, the material is for use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JDFF epoxy powder coating’. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s instructions (Procedure #: Pc-01-3, Work Instruction #: JDFF WI-Pc-01-3-1, Revision #: 2, Issue #: 5, date: 10-01-2023). Cure for 2½ minutes at 232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'Cleantech PW'. Factory applied, two-component, red coloured epoxy coating. Mix component A and component B in a volume ratio of 3:1 and apply as per manufacturer's product data sheet 'CCPL/TDS/R11/CRC/17-18/04/R6/spray'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured fusion bonded epoxy powder coating. Apply as per manufacturer's Product Information '704G_TDS', revised 'August 16,2022'. Post-cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the post-curing conditions that appear on the approval. If the post-cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions reference 'XA12312', dated 26/12/2022. Cure for 15 minutes@220°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
Page 654 of 1165
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
