'Jotapipe IL 6001-120S'. Factory applied, blue coloured, fusion bonded epoxy powder coating. Pre-heat substrate to be coated for 15 minutes@200°C and coating applied as per manufacturer's TDS dated '22 August 2018'. Post-cure for 15 min@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chosui Coat Grey'. Factory applied, grey coloured (once mixed and applied), two-component epoxy resin coating, Mix base:hardener in a 2:1 weight ratio and apply as per PDS 'CN：IF438122003', dated '03/06/2022'. Cure for 7 days@30°C and then 7 days@60°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F I'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's PDS '4384-23-403' dated '2023/11/16'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
‘Permabond A011 Red, A025 Orange, A113 Blue, A115 Orange, A118 Green, A130 Blue, A131 White, A134 Green, A136 Red, A140 Green, A1042 Blue, A1044 White, A1058 Off White, F200 Brown, F201 Brown, F202 Brown, A1084 Yellow & F201HV (translucent)’. Anaerobic adhesives to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of stainless steel calorifiers. Max working pressure 10 bar. Max operating temperature 90°C.
GRPBP range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Range of single hole bidet combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork and single lever operating member. The swivel nozzle outlet incorporates a plastic aerator and the product is supplied with a lever type pop-up waste – not verified by test. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Page 65 of 101
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
