`Talbot, Atplas, Ebco & S Booth` ranges of injection moulded, acetal fittings. Talbot fittings available in: F10 black, F20 blue, F20 black, F10 natural, F20 natural & F20 black. Atplas fittings available in: F10 natural, F20 natural, F20 natural & F20 red. Ebco fittings available in: F10 natural, F20 natural, F20 blue, F20 red, F20 yellow & F20 black. S Booth fittings available in: F20 natural. For use with water up to 60°C.
'ENDOPRENE® 860'. Factory applied, cream coloured, two-part Polyurethane coating. Mix parts A and B in a 66:34 volume ratio and apply as per manufacturer's TDS dated '26/05/2023'. Cure for 50 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NF 131118'. Factory applied, grey coloured, two-part, water-based epoxy coating. Mix resin and curing agent in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V1', dated '20240423'. Cure for 60 minutes@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 864'. Factory applied, cream coloured, two-part Polyurethane coating. Mix parts A and B in a 66:34 volume ratio and apply as per manufacturer's TDS dated '26/11/2024'. Cure for 50 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM III/B-SR - Ramco Slag'. Factory applied, grey coloured Portland Slag Cement. Mix cement:sand:water in a 0.6:1.0:0.22 weight ratio and apply as per manufacturer's work instructions 'WP-08-05 I, issue no. 04, Rev. 0', dated '22.08.2024'. Cure for 24 hours at 27°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GM2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'GMSM01' dated '2024.11.16'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Dicoat 60 EX Blue'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's user instructions 'SPL/R&D/TTD/UI/007', version '01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPONICS WP-NS (No. 20170209)'. Factory applied, dark grey coloured, two-component, solvent free epoxy resin coating consisting of a base and hardener. Mix base and hardener in a weight ratio of 7:3 and apply as per Product Data Sheet ‘1838-K’ dated February 2017. Cure for 168 hours@30°C, then 168 hours@60°C and 'rest' for 168 hours before use. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPS GRP fitting'. Multi-layered fitting comprising of a pale green coloured inner layer and yellow/brown coloured outer layer, manufactured by hand-layup. For use with water up to 60°C.
'Ecoleader® EL-4300'. Dark Yellow coloured (transparent), Vinyl Ester Resin material manufactured by casting moulding process. For use with water up to 60°C.
Page 623 of 887
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
