Range of polyethylene pressure vessels with spun fibreglass casing. Maximum working pressure 10.0 bar Maximum operating temperature 50°C.

Section:

2470 Water Softeners

Section Subtitle:

Components, pressure vessels.

WRAS Approval Number:

251102710

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Q-xxyy-A* and Q-xxyy-P*: 2½” NPSM (F). C-xxyy-A*- NI: 4” UN (F).

Marking:

Pentair logo, model number and technical data on adhesive label on body.

Installation Requirements:

R001

Expiry date:

30/11/2030

Model:

Q-xxyy-A*, Q-xxyy-P*, C-xxyy-A*- NI. Where: xx (External diameter in inches): Q-xxyy-A*: 6 - 13. Q-xxyy-P*: 10 - 12. C-xxyy-A*- NI: 14 - 21. yy (Vessel height in inches): Q-xxyy-A*: 13 - 54. Q-xxyy-P*: 44 - 52. C-xxyy-A*- NI: 43 - 65. A = Indicates top opening in the tank. P = Indicates top opening with pole piece at the bottom of the tank. * relates to non-water contact specifications and will be replaced by details to confirm: - External Colour, - Presence base on the tank, - Chamfer, - Packaging.

Approval Holder:

Pentair International S.a.r.l.

Company Name

Pentair International S.a.r.l.

Address

Voie du Chariot 3, 1003 Lausanne

Country

Switzerland

View All Listings by this Company

'GDPA PermaCoat'. Factory applied, blue coloured (once applied) coating system comprising of a Yellow Zinc Primer and Polyamide top coat. Apply one coat of Yellow Zinc as per work instructions 'PR/WI/01', revision '00', dated '22/11/2017', plating for 45 minutes@30°C. Apply one coat of top coat as per work instructions 'BR/WI/01', revision '00', dated '29/10/2010' and cure for 30 minutes@215°C. For use with water up to 23°C. This material is only approved for the plating and curing conditions that appear on the approval. If the plating and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

250955070

Expiry date:

30/09/2030

Approval Holder:

GDPA Fasteners

Company Name

GDPA Fasteners

Address

GDPA House, Near Rly Godowns Jalandhar, 144004 Punjab

Country

India

View All Listings by this Company

'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

260155012

Expiry date:

31/01/2031

Approval Holder:

Henkel Ltd.

Company Name

Henkel Ltd.

Address

Technologies House, Wood Lane End, Hemel Hempstead

Postcode

HP2 4RQ

Country

Herts

Phone

+44 1442 278 100

General Email

loctite.connect@henkel.com

View All Listings by this Company

'ELTEX® SUPERSTRESS TUB121N9000'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.

Section:

5245 Polyethylene

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

251055071

Expiry date:

31/10/2030

Approval Holder:

INEOS Services Belgium

Company Name

INEOS Services Belgium

Address

Rue de Ransbeek 310, B-1120 Brussels

Country

Belgium

View All Listings by this Company

'ECOTRAN E2130W(#) NC'. Natural (appears beige) PPS material manufactured using Melt compounding method. For use with water up to 85°C.

Section:

5255 Polyphenylene Sulphide (PPS)

Expiry date:

30/11/2030

Approval Holder:

HDC POLYALL CO., Ltd.

Company Name

HDC POLYALL CO., Ltd.

Address

591-1, Sinhang-ro, Nam-gu, Ulsan

Country

Korea, Republic of

View All Listings by this Company