'EP-I-103'. Factory applied, blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturer's instructions issue 'EPOXY86315', dated 'Nov. 15th, 2020'. For use with water up to 65°C.
'Rilsan (MagnaCoat 5501 F)'. Factory applied, white coloured (opaque), polyamide powder coating. Apply as per manufacturer's instructions dated 02/01/2018. Cure for 10 minutes@230°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC1 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-001 issue 1' dated 09-08-2016. For use with water up to 85°C.
"Bond-It Tanking Slurry". Site applied, grey coloured, two part (powder & water) cementitious waterproof coating. Mix and apply as per manufacturer`s instructions 'Version 9' dated 06/08/20. Cure for 12 days at 7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'568H+L101'. Natural (appears off-white in colour), injection moulded GRP material. For use with water up to 70°C.
`8601-A`. Extruded, dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. Shore hardness 85. For use with water up to 85°C.
'Plustek PA303G6BK16'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'LATAMID 66 H2 G/30 BLACK F:3352'. Black coloured, injection moulded PA66 material. For use with water up to 65°C.
'Xytrex 116'. Dark grey coloured, hot compression moulded PEEK washer. For use with water up to 85°C.
'AO Roto Water Tank Panel'. White coloured, LLDPE tank panel manufactured by rotational moulding. For use with water up to 60°C.
'Hostalen CRP100 Black & Hostalen CRP100 RESIST CR Black'. Black coloured HDPE materials, manufactured in Saudi Arabia and Germany, for injection moulding and extrusion purposes. For use with water up to 60°C.
'Total 3581 Blue Polyethylene & Total 3581 Black Polyethylene'. Blue or black coloured, polyethylene material manufactured by rotational moulding. For use with water up to 65°C.
'Total 4041 Blue Polyethylene & Total 4041 Black Polyethylene'. Blue or black coloured, polyethylene material manufactured by rotational moulding. For use with water up to 65°C.
'Helisystem CT fitting'. Green coloured, injection moulded PP-RCT fitting. Between July 2021 and September 2022, the fitting was for use with water up to 23°C. Between October 2022 and July 2026, the fitting is for use with water up to 75°C.
'RTP 499 X 129130 A Natural & RTP 499 X 136502 Natural'. Natural (appear grey in colour), injection moulded polystyrene materials. For use with water up to 50°C.
'Chang QI/CFPC'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
'Art. 0985077205 Anti-leak Tape'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet version '001' dated 26.07.2021. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`1025 Titan Bladder`. Black coloured, calendared butyl rubber sheet material. Shore hardness 60. Tested in-radius size 0.5mm. For use with water up to 23°C.
'EP7008S 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 60°C.
Page 61 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
