'Rashmi Blast Furnace Slag Cement Mortar'. Factory applied, grey coloured, blast furnace slag cement mortar. Mix cement, sand & water in a mass ratio of 1:1.5:0.6 and apply as per manufacturer's work instructions 'RML/DI/WI/CMLC-10', 'Rev: 02', dated '12.10.2023'. Cure for 120 minutes@50°C, 98% RH. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SF2400/2800'. Green coloured, nitrile rubber/aramid material manufactured by calendering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Novus 30'. Orange coloured, nitrile rubber/aramid fibre gasket material manufactured by calandering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Grasso L. 100 Lubricating Grease'. White coloured grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'BADAMID A70 GF50 HE WL BLACK'. Black coloured, injection moulded, glass fibre reinforced PA66 material. For use with water up to 85°C.
'BADAMID A70 GF30 HE WL BLACK'. Black coloured, injection moulded, glass fibre ranforced PA66 material. For use with water up to 85°C.
'Grivory GV XE 10726 Black 9225'. Black coloured, injection moulded, glass reinforced polyamide material. For use with water up 23°C.
'Takweenplast Series HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'OL01 HDPE Fitting'. Black coloured, injection moulded HDPE fitting. For use with water up to 60°C.
'Reinert-Ritz PE 100 Fittings'. Black coloured, extruded polyethylene fittings. For use with water up to 85°C.
'IFAN2100-2'. Extruded, multi-layered pipe comprising of natural (appears white) PEX inner layer, aluminium barrier layer and white coloured PEX outer layer. For use with water up to 85°C.
'BADATRON PPS GF40 WL BLACK'. Black coloured, injection moulded, glass fibre reinforced PPS material. For use with water up to 85°C.
'PVDF Solef® 1011/0001'. White/off-white coloured (translucent), injection moulded PVDF material. For use with water up to 85°C.
'PVDF Solef® 6008/0001'. White/off-white coloured (translucent), injection moulded PVDF material. For use with water up to 85°C.
'E7053AA'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.35mm and 5.0mm. For use with water up to 85°C.
'5594903 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 90. Tested in-radii sizes between 0.4mm and 3.65mm. For use with water up to 85°C.
'5594821'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'5594610'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'5594710'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'silicone RS7007'. Translucent, colourless, compression moulded silicone rubber material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
Page 589 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
